oSIST prEN 10249-1:2006

SLOVENSKI STANDARD
01-junij-2006
+ODGQRREOLNRYDQH]DJDWHL]QHOHJLUDQLKMHNHOGHO7HKQLþQLGREDYQLSRJRML
Cold formed steel sheet piling - Part 1: Technical delivery conditions
Kaltgeformte Spundbohlen aus unlegierten Stählen - Teil 1: Technische
Leiferbedingungen
Palplanches en acier formées a froid - Partie 1: Conditions techniques de livraison
Ta slovenski standard je istoveten z: prEN 10249-1
ICS:
77.140.45 Nelegirana jekla Non-alloyed steels
77.140.70 Jekleni profili Steel profiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2006
ICS 77.140.70 Will supersede EN 10249-1:1995
English Version
Cold formed steel sheet piling - Part 1: Technical delivery
conditions
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 10.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10249-1:2006: E
worldwide for CEN national Members.

Contents
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .5
4 Information to be supplied by the purchaser .5
5 Mass of steel .5
6 Classification and designation.5
7 Technical requirements .6
8 Inspection and testing.8
9 Marking .10
10 Options .11
11 Evaluation of Conformity.11
Annex C Evaluation of conformity.17
C.1 General.17
C.2 Initial type testing by the manufacturer .17
C.2.1 General.17
C.2.2 Intensive routine testing .18
C.2.3 Documentation.18
C.3 Testing of samples taken at the factory by the manufacturer .18
C.4 Factory production control (FPC) .18
C.4.1 General.18
C.4.2 Equipment .18
C.4.3 Raw materials.19
C.4.4 Product testing and evaluation .19
C.4.5 Non-conforming products .19
Continuous surveillance, assessment and approval of factory production control (FPC). .20
C.1General.20
C.4.6 Routine inspection .20
C.4.7 Extraordinary inspection .20
C.4.8 Measures in case of non-conformity.20
Annex ZA (informative)  Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive .21
ZA.1 Scope and relevant characteristics .21
ZA.2 Procedure(s) for the attestation of conformity of hot rolled steel sheet-piling .22
ZA.2.1 Systems of attestation of conformity .22
ZA.2.2 EC certificate and declaration of conformity.23
ZA.3 CE marking and labelling.24

Foreword
This document (prEN 10249-1:2006) has been prepared by Technical Committee ECISS/TC 10 “Structural steels -
Grades and qualities”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10249-1:1995.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of the EU Construction Products
Directive(89/106/EEC)).
For relationship with EU Construction Products Directive (89/106/EEC)), see informative Annex ZA, which is an
integral part of this document.
1 Scope
This part of this European Standard specifies the requirements for cold formed non alloy and alloy steel sheet piling
produced from hot rolled strip or sheet with a thickness equal to or greater than 2 mm in respect of its chemical
composition, mechanical and technological properties and delivery conditions.
The products specified are for general, structural and civil engineering works.
Requirements concerning the tolerances on shape and dimensions are specified in Part 2 of this European
Standard.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 1011-2, Welding – Recommendations for welding of metallic materials – Part 2 : Arc welding of ferritic steels
EN 10002-1, Metallic materials - Tensile testing - Part 1 : Method of test at ambient temperature.
EN 10020, Definition and classification of grades of steel.
EN 10021, General technical delivery requirements for steel and steel products.
EN 10025-2, Hot rolled products of structural steels – Part 2 : Technical delivery conditions for non alloy structural
steels.
EN 10027-1, Designation system for steel - Part 1 : Steel names principal symbols.
EN 10027-2, Designation system for steel - Part 2 : Steel numbers.
EN 10079, Definition of steel products.
EN 10111, Hot rolled non coated mild unalloyed sheet and strip for cold forming. Technical delivery conditions
rEN 10149-1, Hot rolled flat products made of high yield strength steels for cold forming - Part 1 : General delivery
conditions
EN 10149-2, Hot rolled flat products made of high yield strength steels for cold forming - Part 2 : Delivery conditions
for thermomechanical rolled steels.
EN 10149-3, Hot rolled flat products made of high yield strength steels for cold forming - Part 3 : Delivery conditions
for normalized/normalized rolled steels.
EN 10168, Iron and steel products − Inspection document – Contents
EN 10204, Metallic products - Types of inspection documents.
prEN 10249-2, Cold formed steel sheet piling - Part 2 :Tolerances on shape and dimensions.
EN ISO 377, Steel and steel products – Location and preparation of samples and test pieces for mechanical testing.
EN ISO 14284, Steel and iron – Sampling and preparation of samples for the determination of chemical
composition.
CR 10261, ECISS Information Circular 11 - Iron and steel - Review of available methods of chemical analysis
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 10020, EN 10021 and EN
10079 and the following apply.
3.1 cold formed sheet piling
Products made by cold forming on a rolling machine or on a brake press ; the form of the product is such that when
interlocking their joints or overlapping the profiles ends, they constitute a continuous sheet piling structure.
4 Information to be supplied by the purchaser
4.1 General
The following information shall be supplied by the purchaser, at the time of the enquiry and order :
a) details of the product form, length, quantity and any further processing work that is required, e.g. surface
treatment,
b) the designation of the product (in accordance with 6.2),
c) whether products have to be submitted to inspection and testing and if inspection and testing is required, which
type of inspection and which inspection document is required (see 8.1.2).
Where no specific choice is made by the purchaser concerning a) and b), the supplier shall refer back to the
purchaser.
NOTE It is recommended that the manufacturer be informed by the purchaser at the time of the order , if the purchaser
intends to carry out any surface treatment on the product after delivery.
4.2 Options
A number of options are specified in clause 10. In the event that the purchaser does not indicate a requirement to
implement any of these options, the product shall be supplied in accordance with the basic specification.
5 Mass of steel
The calculated mass shall be determined using a conventional volumetric mass of 7,85 kg/dm .
6 Classification and designation
6.1 Classification
This European Standard considers seven steel grades suitable for cold forming :
� Steel EN10025-2 – S235JRC
� Steel EN10025-2 – S275JRC
� Steel EN10025-2 – S355J0C
� Steel EN10149-2 – S355MC
� Steel EN10149-3 – S355NC
� Steel EN10149-2 – S420MC
� Steel EN10149-3 – S420NC
6.2 Designation
)
6.2.1 Steel names  are assigned to steel grades in accordance with EN 10027-1. Steel numbers are allocated to
steel grades in accordance with EN 10027-2.
6.2.2 The products covered by this European Standard shall be designated in the following sequence :
a) the name of the product, i.e. "Sheet piling",
b) the number of this European Standard, i.e. EN 10249,
c) the steel name or number.
EXAMPLE : Sheet piling EN 10249-S235JRC or Sheet piling EN 10249-1.0122
indicates a sheet piling in accordance with EN 10249 made of steel S235JRC (Steel number 1.0122).
7 Technical requirements
7.1 Steel manufacturing process
7.1.1 The steel manufacturing process shall be at the manufacturer's option. Where specified at the time of the
enquiry and order, the steel manufacturing proce
...