SIST EN 1028-1:2003
(Main)Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 1: Classification - General and safety requirements
Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 1: Classification - General and safety requirements
This standard applies for centrifugal pumps with priming devices for fire-fighting use supplied separately without driver and couplings. Fire-fighting centrifugal pumps with primer are defined as terminated by their inlet and outlet connec-tions as well as by their shaft ends.
This standard applies for fire-fighting centrifugal pumps with priming devices for use under ambient temperatu-res between -15 °C and 40 °C.
NOTE For special conditions, -30 °C; see 6.12.
This standard does not apply to fire-fighting centrifugal pumps with primer of which the only power source is directly applied manual effort.
This standard specifies the classification and general requirements for fire-fighting centrifugal pumps with priming devices with a nominal delivery rate of up to 6000 l/min.
This standard deals with significant hazards listed in clause 4, hazardous situations and events during the commis-sio-ning, operation and maintenance of fire-fighting centrifugal pumps with priming devices, used as intended and under the conditions foreseen by the manufacturer or the manufacturer's authorized representati-ve. In addition, fire-fighting centrifugal pumps with priming devices shall conform as appropriate to EN 292 for hazards not covered by this standard.
This standard does not deal with the detailed verification of general and safety requirements and/or protective measures. These are covered in prEN 1028-2 "Verification of general and safety requirements".
This standard does not deal with the technical safety requirements for the design or manufacture of drivers or of auxiliary equipment. It does not cover risks directly arising from means provided for the portability, trans-portability, and mobility of pump units during or between periods of operation, or requirements for transmission shafts linking self-propelled machinery to a pump. In addition, this standard does not cover:
Feuerlöschpumpen - Feuerlöschkreiselpumpen mit Entlüftungseinrichtung - Teil 1: Klassifizierung - Allgemeine und Sicherheitsanforderungen
Dieses Dokument ist eine Typ C-Norm wie in EN 292 und EN 1070 angegeben.
Auf die betreffenden Maschinen und die behandelten Gefährdungen, Gefährdungssituationen und Gefährdungs-ereignisse wird im Anwendungsbereich dieses Dokuments hingewiesen.
Für Maschinen, die nach den Festlegungen dieser Typ C-Norm konzipiert und gebaut worden sind, gilt: Wenn Festlegungen in dieser Typ C-Norm von Festlegungen in Typ A- oder B-Normen abweichen, haben die Festlegungen dieser Typ C-Norm Vorrang gegenüber den Festlegungen der anderen Normen.
Diese Norm wurde als harmonisierte Norm erarbeitet, die eine Möglichkeit darstellt, die Übereinstimmung mit den grundlegenden Anforderungen der Maschinenrichtlinie und zugehörigen EFTA-Vorschriften zu erfüllen.
Bei der Erarbeitung dieser Norm wurde vorausgesetzt, dass:
a) diese Pumpe nur von geschultem Personal betrieben wird;
b) Bauteile ohne besondere Anforderungen
1) nach üblichen ingenieurtechnischen Praktiken und Berechnungsmethoden, einschließlich sämtlicher Ausfallarten konstruiert wurden;
2) mechanisch solide konstruiert sind;
3) aus Werkstoffen mit angemessener Festigkeit und geeigneter Qualität hergestellt wurden;
4) aus fehlerfreien Werkstoffen hergestellt wurden;
ANMERKUNG Allgemeine Gefährdungen durch hydraulische und pneumatische Einrichtungen werden z. B. in EN 982 und EN 983 behandelt.
c) gefährliche Werkstoffe (z. B. Asbest) nicht als Teil der Pumpe eingesetzt werden;
d) Bauteile in gutem Betriebszustand gehalten werden, damit die geforderten Eigenschaften erhalten bleiben;
e) durch die Bemessung der lasttragenden Elemente ein sicherer Betrieb der Pumpe im Bereich von 0 % bis 100 % der Bemessungswerte und bei den Prüfungen sichergestellt ist;
Pompes a usage incendie - Pompes centrifuges a usage incendie avec dispositif d'amorçage - Partie 1 : Classification - Prescriptions générales et de sécurité
La présente norme s'applique aux pompes centrifuges à usage incendie avec dispositif d'amorçage, fournies sans actionneur et sans accouplement. Les pompes centrifuges à usage incendie avec dispositif d'amorçage sont définies comme étant terminées par leurs orifices d'entrée et de sortie ainsi que par leurs extrémités d'axe.
La présente norme s'applique aux pompes centrifuges avec dispositif d'amorçage à usage incendie pour une utilisation à une température ambiante pouvant varier entre - 15 °C et + 40 °C.
NOTE Pour les conditions spéciales à - 30 °C, voir 6.12.
La présente norme ne s'applique pas aux pompes centrifuges à usage incendie avec dispositif d'amorçage pour lesquelles la seule source d'énergie est la force humaine employée directement.
La présente norme indique la classification et les prescriptions générales relatives aux pompes centrifuges à usage incendie avec dispositif d'amorçage justifiant d'un débit de refoulement pouvant aller jusqu'à 6 000 l/min.
La présente norme traite des phénomènes dangereux significatifs indiqués à l'article 4, des situations et des événements dangereux pendant la mise en service, le fonctionnement et l'entretien des pompes centrifuges à usage d'incendie avec dispositif d'amorçage, quand elles sont utilisées comme prévu et, dans les conditions prévues par le fabricant ou son représentant autorisé. En complément, les pompes centrifuges à usage incendie avec dispositif d'amorçage doivent satisfaire de façon appropriée à l'EN 292 pour les phénomènes dangereux non couverts par la présente norme.
La présente norme ne traite pas des procédures de contrôle des prescriptions générales de performance et de sécurité et/ou des mesures de protection. Celles-ci sont traitées dans le prEN 1028-2 « Vérification des prescriptions générales et de sécurité ».
La présente norme ne traite pas des prescriptions de sécurité en matière de conception ou de fabrication des actionneurs ou des équipements auxiliaires. Elle ne fixe pas les presc
Gasilske črpalke - Gasilske centrifugalne črpalke s sesalno napravo - 1. del: Klasifikacija - Splošne zahteve in zahteve za varnost
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2003
*DVLOVNHþUSDONH*DVLOVNHFHQWULIXJDOQHþUSDONHVVHVDOQRQDSUDYRGHO
.ODVLILNDFLMD6SORãQH]DKWHYHLQ]DKWHYH]DYDUQRVW
Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 1: Classification -
General and safety requirements
Feuerlöschpumpen - Feuerlöschkreiselpumpen mit Entlüftungseinrichtung - Teil 1:
Klassifizierung - Allgemeine und Sicherheitsanforderungen
Pompes a usage incendie - Pompes centrifuges a usage incendie avec dispositif
d'amorçage - Partie 1 : Classification - Prescriptions générales et de sécurité
Ta slovenski standard je istoveten z: EN 1028-1:2002
ICS:
13.220.10 Gašenje požara Fire-fighting
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 1028-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2002
ICS 13.220.10
English version
Fire-fighting pumps - Fire-fighting centrifugal pumps with primer
- Part 1: Classification - General and safety requirements
Pompes à usage incendie - Pompes centrifuges à usage Feuerlöschpumpen - Feuerlöschkreiselpumpen mit
incendie avec dispositif d'amorçage - Partie 1: Entlüftungseinrichtung - Teil 1: Klassifizierung - Allgemeine
Classification - Prescriptions générales et de sécurité und Sicherheitsanforderungen
This European Standard was approved by CEN on 8 April 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1028-1:2002 E
worldwide for CEN national Members.
Contents
Foreword.4
0 Introduction .5
1 Scope .6
2 Normative references .7
3 Terms and definitions.8
3.1 Pumps and their applications.8
3.2 Suction heights .9
3.3 Pressures.9
3.4 Delivery rates.11
3.5 Power .12
3.6 Speed of rotation .12
3.7 Efficiencies .12
3.8 Priming time .12
4 List of significant hazards.13
5 Safety requirements and/or protective measures .15
5.1 General.15
5.2 Special requirements.16
5.2.1 Mechanical hazards .16
5.2.2 Electrical hazards .17
5.2.3 Thermal hazards.17
5.2.4 Hazards from neglecting ergonomic design principles.18
5.2.5 Hazards due to breakdown and/or incorrect installation of protection devices .18
6 General and performance requirements .19
6.1 Design .19
6.2 Materials.19
6.3 Nominal delivery pressure.19
6.4 Nominal delivery rate.19
6.5 Geodetic nominal suction height .19
6.6 Closing pressure.19
6.7 Primer.20
6.8 Drainability.20
6.9 Shut off valves and pump connections.20
6.10 Pump inlet screen .20
6.11 Low temperature starting.20
6.12 Very low temperature behaviour .20
6.13 Operating controls.20
6.14 Additional equipment .20
6.15 Pump integrity protection equipment.20
6.16 Efficiency .21
6.17 Guarantee points.21
6.18 Special tools.21
7 Verification of the safety requirements and/or protective measures.21
8 Verification of the general and performance requirements .21
9 Classification and brief designation .22
10 Designation.23
11 Information for use .23
11.1 General.23
11.2 Signals and warning devices.23
11.3 Accompanying documents.23
11.3.1 General.23
11.3.2 Contents .23
11.4 Marking .28
Annex ZA (informative) Relationship of this document with EC Directives.29
Bibliography .30
Foreword
This document (EN 1028-1:2002) has been prepared by Technical Committee CEN/TC 192 "Fire service
equipment", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by February 2003, and conflicting national standards shall be withdrawn at the latest
by February 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,
Sweden, Switzerland and the United Kingdom.
This part of this European Standard shall be applied only in conjunction with part 2 of EN 1028 "Verification of general
and safety requirements".
EN 1028 "Fire-fighting pumps – Fire-fighting centrifugal pumps with primer" comprises two parts:
– Part 1: Classification — General and safety requirements;
– Part 2: Verification of general and safety requirements.
0 Introduction
This European Standard is a type C standard as stated in EN 292 and EN 1070.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this standard.
Where provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines that have
been designed and built in accordance with the provisions of this type C standard.
This Standard has been prepared as a harmonized standard to provide one means of conformity with essential
requirements of the Machinery Directive and associated EFTA Regulations.
While producing this standard it was assumed that:
a) only trained persons operate the machine;
b) components without specific requirements are:
1) designed in accordance with the usual engineering practice and calculation codes, including all failure
modes;
2) of sound mechanical construction;
3) of materials with adequate strength and of suitable quality;
4) of materials free of defects;
NOTE General hazards due to hydraulic and pneumatic equipment are dealt with in standards for common use such as
EN 982, EN 983.
c) harmful materials (e.g. asbestos) are not used as part of the machine;
d) components are kept in good repair and working order, so that the required characteristics remain;
e) by design of the load bearing elements, a safe operation of the machine is assured for loading, from 0 % to
100 % of the rated possibilities and during the tests;
f) to ensure the correct functioning of the equipment, the ambient temperature is maintained between -15 C (for
special conditions, -30 C; see 6.12) and 40 C;
NOTE Directly around the pump the temperature can be 20 C higher.
g) the manufacturer and the user have agreed the features of the machinery and the operating conditions;
h) the place of installation enables safe usage of the machine.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.