SIST EN ISO 22553-8:2021

SLOVENSKI STANDARD
01-november-2021
Barve in laki - Elektrodepozicijski premazi - 8. del: Gostota električnega naboja
(ISO 22553-8:2020)
Paints and varnishes - Electro-deposition coatings - Part 8: Electric charge density (ISO
22553-8:2020)
Beschichtungsstoffe - Elektrotauchlacke - Teil 8: Abscheideäquivalent (ISO 22553-
8:2020)
Peintures et vernis - Peintures d'électrodéposition - Partie 8: Charge électrique
volumique (ISO 22553-8:2020)
Ta slovenski standard je istoveten z: EN ISO 22553-8:2021
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 22553-8
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2021
EUROPÄISCHE NORM
ICS 87.040
English Version
Paints and varnishes - Electro-deposition coatings - Part 8:
Electric charge density (ISO 22553-8:2020)
Peintures et vernis - Peintures d'électrodéposition - Beschichtungsstoffe - Elektrotauchlacke - Teil 8:
Partie 8: Charge électrique volumique (ISO 22553- Abscheideäquivalent (ISO 22553-8:2020)
8:2020)
This European Standard was approved by CEN on 23 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22553-8:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 22553-8:2020 has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes” of the International Organization for Standardization (ISO) and has been taken over as
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall
be withdrawn at the latest by March 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22553-8:2020 has been approved by CEN as EN ISO 22553-8:2021 without any
modification.
INTERNATIONAL ISO
STANDARD 22553-8
First edition
2020-06
Paints and varnishes — Electro-
deposition coatings —
Part 8:
Electric charge density
Reference number
ISO 22553-8:2020(E)
©
ISO 2020
ISO 22553-8:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 22553-8:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials. 2
6 Test panels . 3
7 Number of determinations . 3
8 Sample preparation . 3
9 Procedure. 4
10 Evaluation . 5
10.1 Electric charge density per unit mass . 5
10.2 Electric charge density per unit volume . 5
11 Precision . 6
12 Test report . 6
Annex A (informative) Calculation of the electric charge density per unit mass using the
practical or theoretical dry-film thickness in accordance with ISO 3233-2 or ISO 3233-3 .8
Bibliography .10
ISO 22553-8:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes.
A list of all parts in the ISO 22553 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

ISO 22553-8:2020(E)
Introduction
The electric charge density provides information about the efficiency of the deposition process during
electro-deposition coating.
If measurement of the electrical wet-film resistance in accordance with ISO 22553-7 is necessary, this
can be specified in the test assembly provided.
INTERNATIONAL STANDARD ISO 22553-8:2020(E)
Paints and varnishes — Electro-deposition coatings —
Part 8:
Electric charge density
1 Scope
This document specifies a method for determining the electric charge density of an electro-deposition
coating (e-coat) for automotive industries and other general industrial applications, e.g. chiller units,
consumer products, radiators, aerospace, agriculture.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
...