SIST EN 301 575 V1.1.1:2012
(Main)Environmental Engineering (EE) - Measurement method for energy consumption of Customer Premises Equipment (CPE)
General Information
- Abstract
Define the methodology and the tests conditions to measure the power consumption of end-user broadband equipment (CPE) within the scope of EU regulation 1275/2008 in Off mode (as defined in Commission Regulation 1275/2008) Standby (as defined in Commission Regulation 1275/2008) Networked Standby / Low Power states On mode
- Status
- Published
- Publication Date
- 29-May-2012
- Technical Committee
- SPN - Services and Protocols for Networks
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 17-May-2012
- Due Date
- 22-Jul-2012
- Completion Date
- 30-May-2012
- Mandate
- M/439
Buy Documents
en_301575v010101o - Environmental Engineering (EE); Measurement method for energy consumption of Customer Premises Equipment (CPE)
en_301575v010101p - Environmental Engineering (EE); Measurement method for energy consumption of Customer Premises Equipment (CPE)
Overview
SIST EN 301 575 V1.1.1:2012 is a European standard developed by SIST, harmonized with ETSI EN 301 575 V1.1.1, that specifies a consistent methodology for measuring the energy consumption of Customer Premises Equipment (CPE). CPE is a category of broadband equipment located at end users' premises, critical for telecommunications and internet access services. This standard supports compliance with EU Regulation 1275/2008, which sets ecodesign requirements for standby and off-mode power consumption of household and office electronic devices.
By defining clear, reproducible test conditions and measurement procedures for CPE across various operational states-off, standby, idle, low power, and on-SIST EN 301 575 helps manufacturers, labs, and regulators assess and improve the energy efficiency of broadband-connected equipment.
Key Topics
- Measurement Methodology: Detailed measurement setup for CPE energy consumption in accordance with environmental engineering principles, including guidelines on laboratory conditions and equipment calibration.
- Operational Modes Defined: Explanation of CPE operation modes relevant for measurement:
- Off mode: Device connected to mains but providing no functions.
- Standby mode: Device supports only basic reactivation or display functions.
- Idle state: Device powered, but no significant user traffic.
- Low power/networked standby: Energy-saving configurations, often user-adjustable.
- On mode: At least one primary function is active.
- Measurement Requirements:
- Laboratory conditions (25°C ± 2°C, 30%–75% relative humidity)
- Use of calibrated measurement instruments with high precision (±1% tolerance)
- Combined use of power analyzers, voltmeters, and ammeters for accurate real, apparent, and power factor measurements
- Test Configurations and Scenarios: Prescribed setups for measuring power in each operational mode, ensuring consistent and comparable results across testing sites.
- Exclusions: Equipment powered exclusively through network connections or USB (e.g., Power over Ethernet or USB-powered devices) falls outside the standard’s scope.
Applications
SIST EN 301 575 V1.1.1 is essential for several stakeholders in the broadband and telecommunications sectors:
- Manufacturers: Enables consistent evaluation and improvement of CPE energy performance, a key factor for product eco-labeling, marketability, and regulatory compliance.
- Testing Laboratories: Provides standardized test protocols, ensuring traceable and credible results that support declarations and certifications.
- Regulators & Compliance Auditors: Supplies a harmonized framework for enforcing ecodesign rules, supporting the EU’s energy efficiency objectives and reducing household and office energy consumption.
- Product Developers: Guides the development of energy-efficient features such as advanced standby and low-power states, contributing to sustainability targets.
- Procurement and Eco-labeling Programs: Assists in verifying claims regarding the energy efficiency of customer premises equipment for public and private sector procurement.
Related Standards
This standard operates in conjunction with several key regulations and technical standards:
- Commission Regulation (EC) No 1275/2008: Establishes ecodesign requirements for standby and off-mode electric power consumption.
- CENELEC EN 50160: Specifications for voltage characteristics of electricity supplies.
- European Code of Conduct on Energy Consumption of Broadband Communication Equipment
- IEEE 802.16: Standards for local and metropolitan area broadband wireless access.
- CableLabs DOCSIS® Specifications: Outlines data-over-cable service interface specifications.
- ITU-T G.993.2: Defines technical requirements for VDSL2 DSL equipment.
For organizations aiming for sustainable practices and adherence to European environmental directives, SIST EN 301 575 provides the foundational methodology for accurately measuring and optimizing CPE energy consumption.
Buy Documents
en_301575v010101o - Environmental Engineering (EE); Measurement method for energy consumption of Customer Premises Equipment (CPE)
en_301575v010101p - Environmental Engineering (EE); Measurement method for energy consumption of Customer Premises Equipment (CPE)
Get Certified
Connect with accredited certification bodies for this standard
IMP NDT d.o.o.
Non-destructive testing services. Radiography, ultrasonic, magnetic particle, penetrant, visual inspection.
Inštitut za kovinske materiale in tehnologije
Institute of Metals and Technology. Materials testing, metallurgical analysis, NDT.
Q Techna d.o.o.
NDT and quality assurance specialist. 30+ years experience. NDT personnel certification per ISO 9712, nuclear and thermal power plant inspections, QA/
Sponsored listings
Frequently Asked Questions
SIST EN 301 575 V1.1.1:2012 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Environmental Engineering (EE) - Measurement method for energy consumption of Customer Premises Equipment (CPE)". This standard covers: Define the methodology and the tests conditions to measure the power consumption of end-user broadband equipment (CPE) within the scope of EU regulation 1275/2008 in Off mode (as defined in Commission Regulation 1275/2008) Standby (as defined in Commission Regulation 1275/2008) Networked Standby / Low Power states On mode
Define the methodology and the tests conditions to measure the power consumption of end-user broadband equipment (CPE) within the scope of EU regulation 1275/2008 in Off mode (as defined in Commission Regulation 1275/2008) Standby (as defined in Commission Regulation 1275/2008) Networked Standby / Low Power states On mode
SIST EN 301 575 V1.1.1:2012 is classified under the following ICS (International Classification for Standards) categories: 19.040 - Environmental testing. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 301 575 V1.1.1:2012 is associated with the following European legislation: Standardization Mandates: M/439. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 301 575 V1.1.1:2012 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Final draft ETSI EN 301 575 V1.1.1 (2011-11)
European Standard
Environmental Engineering (EE);
Measurement method for energy consumption of Customer
Premises Equipment (CPE)
2 Final draft ETSI EN 301 575 V1.1.1 (2011-11)
Reference
DEN/EE-00021
Keywords
CPE, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 301 575 V1.1.1 (2011-11)
Contents
Intellectual Property Rights . 4
Foreword . 4
Introduction . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions and abbreviations . 6
3.1 Definitions . 6
3.2 Abbreviations . 6
4 Operating modes . 7
5 General requirements for measurement conditions . 7
5.1 Measurement conditions . 7
5.2 Measurement instruments requirements . 8
6 Measurement configurations . 8
6.1 Off mode . 8
6.2 Standby mode . 9
6.3 Idle state . 9
6.4 On mode . 10
Annex A (informative): Bibliography . 13
History . 14
ETSI
4 Final draft ETSI EN 301 575 V1.1.1 (2011-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering
(EE), and is now submitted for the ETSI standards One-step Approval Procedure.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Introduction
The present document defines the energy consumption measurement methods for CPE telecommunication equipment.
ETSI
5 Final draft ETSI EN 301 575 V1.1.1 (2011-11)
1 Scope
The present document defines the methodology and the tests conditions to measure the power consumption of end-user
broadband equipment (CPE) within the scope of EU regulation 1275/2008 [1] in:
• Off mode (as defined in Commission Regulation 1275/2008)
• Standby (as defined in Commission Regulation 1275/2008)
• Idle states
• On mode
Moreover, these different modes of operation are defined.
The methods of measurement are applicable to customer premises equipment which can be directly connected to the
mains.
Equipment drawing electricity via the network connection (indirectly connected to the mains) is out of scope.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] "Code Of Conduct on Energy Consumption of Broadband Communication Equipment" European
Commission Directorate-General, Joint Research Centre; Final v4: 10 February 2011.
[i.2] IEEE 802.16: "IEEE Standard for Local and metropolitan area networks Part 16: Air Interface for
Broadband Wireless Access Systems".
[i.3] Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on
the approximation of the laws of the Member States relating to electromagnetic compatibility and
repealing Directive 89/336/EEC.
[i.4] CENELEC EN 50160: "Voltage characteristics of electricity supplied by public electricity
networks".
ETSI
6 Final draft ETSI EN 301 575 V1.1.1 (2011-11) ®
[i.5] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS 2.0 Interface". ®
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS 3.0 Interface".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following definitions apply:
broadband telecommunication network equipment: equipment of broadband technology that is part of a
telecommunication network
broadband terminal equipment: equipment of broadband technology that is connected to a telecommunication
network at a point beyond the Network Termination Point
Customer-Premises Equipment (CPE): any terminal and associated equipment located at a subscriber's premises and
connected with a carrier's telecommunication channel(s) at the Network Termination Points (NTPs)
directly connected to the mains: equipment that could draw electricity from mains power outlet itself via its internal
or external power
...
European Standard
Environmental Engineering (EE);
Measurement method for energy consumption of Customer
Premises Equipment (CPE)
2 ETSI EN 301 575 V1.1.1 (2012-05)
Reference
DEN/EE-00021
Keywords
CPE, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2012.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 575 V1.1.1 (2012-05)
Contents
Intellectual Property Rights . 4
Foreword . 4
Introduction . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions and abbreviations . 6
3.1 Definitions . 6
3.2 Abbreviations . 6
4 Operating modes . 7
5 General requirements for measurement conditions . 7
5.1 Measurement conditions . 8
5.2 Measurement instruments requirements . 8
6 Measurement configurations . 8
6.1 Off mode . 8
6.2 Standby mode . 9
6.3 Idle state . 9
6.4 On mode . 10
Annex A (informative): Bibliography . 13
History . 14
ETSI
4 ETSI EN 301 575 V1.1.1 (2012-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).
National transposition dates
Date of adoption of this EN: 28 March 2012
Date of latest announcement of this EN (doa): 30 June 2012
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2012
Date of withdrawal of any conflicting National Standard (dow): 31 December 2012
Introduction
The present document defines the energy consumption measurement methods for Broadband CPE telecommunication
equipment.
ETSI
5 ETSI EN 301 575 V1.1.1 (2012-05)
1 Scope
The present document defines the methodology and the tests conditions to measure the power consumption of end-user
broadband equipment (CPE) within the scope of EU regulation 1275/2008 [1] in:
• Disconnected mode
• Off mode (as defined in Commission Regulation 1275/2008)
• Standby (as defined in Commission Regulation 1275/2008)
• Idle states
• Low Power states
• On mode
Moreover, these different modes of operation are defined.
The methods of measurement are applicable to customer premises equipment which can be directly connected to the
mains.
Equipment drawing electricity via the network connection (indirectly connected to the mains) or via local Personal
Computer (i.e. via USB) is out of scope.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] "Code Of Conduct on Energy Consumption of Broadband Communication Equipment" European
Commission Directorate-General, Joint Research Centre; Final v4: 10 February 2011.
[i.2] IEEE 802.16: "IEEE Standard for Local and metropolitan area networks Part 16: Air Interface for
Broadband Wireless Access Systems".
ETSI
6 ETSI EN 301 575 V1.1.1 (2012-05)
[i.3] Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on
the approximation of the laws of the Member States relating to electromagnetic compatibility and
repealing Directive 89/336/EEC.
[i.4] CENELEC EN 50160: "Voltage characteristics of electricity supplied by public electricity
networks". ®
[i.5] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS 2.0 Interface". ®
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS 3.0 Interface".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following definitions apply:
broadband telecommunication network equipment: equipment comprising broadband technology that is part of a
telecommunication network
broadband terminal equipment: equipment comprising broadband technology that is connected to a
telecommunication network at a point beyond the Network Termination Point
Customer-Premises Equipment (CPE): any terminal and associated equipment located at a subscriber's premises and
connected with a carrier's telecommunication channel(s) at the Network Termination Points (NTPs)
directly connected to the mains: equipment that could draw electricity from mains power outlet itself via its internal
or external power supply
indirectly connected to the mains power sou
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Okoljski inženiring (EE) - Merilna metoda za porabo energije opreme pri porabniku (CPE)Environmental Engineering (EE) - Measurement method for energy consumption of Customer Premises Equipment (CPE)19.040Preskušanje v zvezi z okoljemEnvironmental testingICS:Ta slovenski standard je istoveten z:EN 301 575 Version 1.1.1SIST EN 301 575 V1.1.1:2012en01-julij-2012SIST EN 301 575 V1.1.1:2012SLOVENSKI
STANDARD
European Standard SIST EN 301 575 V1.1.1:2012
ETSI ETSI EN 301 575 V1.1.1 (2012-05) 2
Reference DEN/EE-00021 Keywords CPE, power measurement ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2012. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 575 V1.1.1:2012
ETSI ETSI EN 301 575 V1.1.1 (2012-05) 3 Contents Intellectual Property Rights . 4 Foreword . 4 Introduction . 4 1 Scope . 5 2 References . 5 2.1 Normative references . 5 2.2 Informative references . 5 3 Definitions and abbreviations . 6 3.1 Definitions . 6 3.2 Abbreviations . 6 4 Operating modes . 7 5 General requirements for measurement conditions . 7 5.1 Measurement conditions . 8 5.2 Measurement instruments requirements . 8 6 Measurement configurations . 8 6.1 Off mode . 8 6.2 Standby mode . 9 6.3 Idle state . 9 6.4 On mode . 10 Annex A (informative): Bibliography . 13 History . 14
ETSI ETSI EN 301 575 V1.1.1 (2012-05) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).
National transposition dates Date of adoption of this EN: 28 March 2012 Date of latest announcement of this EN (doa): 30 June 2012 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2012 Date of withdrawal of any conflicting National Standard (dow): 31 December 2012
Introduction The present document defines the energy consumption measurement methods for Broadband CPE telecommunication equipment. SIST EN 301 575 V1.1.1:2012
ETSI ETSI EN 301 575 V1.1.1 (2012-05) 5 1 Scope The present document defines the methodology and the tests conditions to measure the power consumption of end-user broadband equipment (CPE) within the scope of EU regulation 1275/2008 [1] in: • Disconnected mode • Off mode (as defined in Commission Regulation 1275/2008) • Standby (as defined in Commission Regulation 1275/2008) • Idle states • Low Power states • On mode Moreover, these different modes of operation are defined. The methods of measurement are applicable to customer premises equipment which can be directly connected to the mains.
Equipment drawing electricity via the network connection (indirectly connected to the mains) or via local Personal Computer (i.e. via USB) is out of scope. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive 2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements for standby and off mode electric power consumption of electrical and electronic household and office equipment. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] "Code Of Conduct on Energy Consumption of Broadband Communication Equipment" European Commission Directorate-General, Joint Research Centre; Final v4: 10 February 2011. [i.2] IEEE 802.16: "IEEE Standard for Local and metropolitan area networks Part 16: Air Interface for Broadband Wireless Access Systems". SIST EN 301 575 V1.1.1:2012
ETSI ETSI EN 301 575 V1.1.1 (2012-05) 6 [i.3] Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC. [i.4] CENELEC EN 50160: "Voltage characteristics of electricity supplied by public electricity networks". [i.5] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS® 2.0 Interface". [i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS® 3.0 Interface". 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following definitions apply: broadband telecommunication network equipment: equipment comprising broadband technology that is part of a telecommunication network broadband terminal equipment: equipment comprising broadband technology that is connected to a telecommunication network at a point beyond the Network Termination Point Customer-Premises Equipment (C
...