SIST EN 300 433-2 V1.3.1:2011

Draft ETSI EN 300 433-2 V1.2.1 (2010-07)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Land Mobile Service;
Citizens' Band (CB) radio equipment;
Part 2: Harmonized EN covering the essential requirements of
article 3.2 of the R&TTE Directive

2 Draft ETSI EN 300 433-2 V1.2.1 (2010-07)

Reference
REN/ERM-TGDMR-266-2
Keywords
CB, radio, regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 300 433-2 V1.2.1 (2010-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements . 8
4.1 Environmental profile . 8
4.2 Transmitter requirements . 8
4.2.1 Frequency error . 8
4.2.1.1 Definition . 8
4.2.1.2 Limit . 8
4.2.1.3 Conformance . 8
4.2.2 Transmitter carrier power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Conformance . 9
4.2.3 Maximum permissible frequency deviation . 9
4.2.3.1 Definition . 9
4.2.3.2 Limit . 9
4.2.3.3 Conformance . 9
4.2.4 Adjacent channel power . 9
4.2.4.1 Definition . 9
4.2.4.2 Limit . 9
4.2.4.3 Conformance . 9
4.2.5 Unwanted emissions in the spurious domain . 9
4.2.5.1 Definition . 9
4.2.5.2 Limits . 9
4.2.5.3 Conformance . 9
4.2.6 Transient behaviour of the transmitter . 9
4.2.6.1 Definition . 9
4.2.6.2 Limits . 9
4.2.6.3 Conformance . 10
4.3 Receiver requirements . 10
4.3.1 Spurious radiations . 10
4.3.1.1 Definition . 10
4.3.1.2 Limits . 10
4.3.1.3 Conformance . 10
5 Testing for compliance with technical requirements . 10
5.1 Environmental conditions for testing . 10
5.1.1 Normal and extreme test-conditions . 10
5.1.2 Test power source . 10
5.1.3 Choice of samples for the measurements . 10
5.2 Interpretation of the measurement results . 10
5.3 Essential test suites . 11
5.3.1 Frequency error . 11
5.3.2 Transmitter carrier power . 11
5.3.3 Maximum permissible frequency deviation . 11
ETSI
4 Draft ETSI EN 300 433-2 V1.2.1 (2010-07)
5.3.4 Adjacent channels power . 11
5.3.5 Unwanted emissions in the spurious domain . 11
5.3.6 Transient behaviour of the transmitter . 11
5.3.7 Receiver spurious radiations . 11
Annex A (normative): HS Requirement and conformance Test specifications Table (HS-
RTT) . 12
Annex B (informative): The EN title in the official languages . 15
History . 16

ETSI
5 Draft ETSI EN 300 433-2 V1.2.1 (2010-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
The requirements relevant to Directive 1999/5/EC are summarised in annex A.
The present document is part 2 of a multi-part deliverable covering Citizens' Band (CB) radio equipment, as identified
below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Equipment only capable of using angle modulation shall be tested according to EN 300 135-1 [i.4].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 [i.3].
ETSI
6 Draft ETSI EN 300 433-2 V1.2.1 (2010-07)
1 Scope
The present document covers the technical requirements for transmitters and receivers used in stations of angle
modulated, Double Side Band (DSB) modulated and/or Single Side Band (SSB) modulated Citizens' Band (CB) radio
equipment operating in all or part of the frequency band 26,960 MHz to 27,410 MHz with a channel spacing of 10 kHz,
and intended for analogue speech and/or data transmission.
Angle modulated Citizens' Band radio equipment (PR 27) operation is in accordance with ERC Decision (98)11 [i.5].
The equipment operates on one or more channels of the carrier frequencies as shown in table 1.
Table 1: Carrier frequencies
Carrier Channel Carrier frequencies Channel
frequencies Number Number
26,965 MHz 1 27,215 MHz 21
26,975 MHz 2 27,225 MHz 22
26,985 MHz 3 27,235 MHz 24
27,005 MHz 4 27,245 MHz 25
27,015 MHz 5 27,255 MHz 23
27,025 MHz 6 27,265 MHz 26
27,035 MHz 7 27,275 MHz 27
27,055 MHz 8 27,285 MHz 28
27,065 MHz 9 27,295 MHz 29
27,075 MHz 10 27,305 MHz 30
27,085 MHz 11 27,315 MHz 31
27,105 MHz 12 27,325 MHz 32
27,115 MHz 13 27,335 MHz 33
27,125 MHz 14 27,345 MHz 34
27,433 MHz 15 27,355 MHz 35
27,155 MHz 16 27,365 MHz 36
27,165 MHz 17 27,375 MHz 37
27,175 MHz 18 27,385 MHz 38
27,185 MHz 19 27,395 MHz 39
27,205 MHz 20 27,405 MHz 40
Transmission and reception takes place on the same channel (single frequency simplex mode).
Any equipment using national regulations on Citizens' Band (CB) permitting the use of channels outside of the carrier
frequencies shown in table 1
...

Final draft ETSI EN 300 433-2 V1.3.1 (2011-05)
Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Citizens' Band (CB) radio equipment;
Part 2: Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive

2 Final draft ETSI EN 300 433-2 V1.3.1 (2011-05)

Reference
REN/ERM-TGDMR-266-2
Keywords
CB, radio, regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2011.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 300 433-2 V1.3.1 (2011-05)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements . 8
4.1 Environmental profile . 8
4.2 Transmitter requirements . 8
4.2.1 Frequency error . 8
4.2.1.1 Definition . 8
4.2.1.2 Limit . 8
4.2.1.3 Conformance . 8
4.2.2 Transmitter power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Conformance . 9
4.2.3 Maximum permissible frequency deviation . 9
4.2.3.1 Definition . 9
4.2.3.2 Limit . 9
4.2.3.3 Conformance . 9
4.2.4 Adjacent channel power . 9
4.2.4.1 Definition . 9
4.2.4.2 Limit . 9
4.2.4.3 Conformance . 9
4.2.5 Unwanted emissions in the spurious domain . 9
4.2.5.1 Definition . 9
4.2.5.2 Limits . 9
4.2.5.3 Conformance . 9
4.2.6 Transient behaviour of the transmitter . 9
4.2.6.1 Definition . 9
4.2.6.2 Limits . 9
4.2.6.3 Conformance . 10
4.3 Receiver requirements . 10
4.3.1 Spurious radiations . 10
4.3.1.1 Definition . 10
4.3.1.2 Limits . 10
4.3.1.3 Conformance . 10
5 Testing for compliance with technical requirements . 10
5.1 Environmental conditions for testing . 10
5.1.1 Normal and extreme test-conditions . 10
5.1.2 Test power source . 10
5.1.3 Choice of samples for the measurements . 10
5.2 Interpretation of the measurement results . 10
5.3 Essential test suites . 11
5.3.1 Frequency error . 11
5.3.2 Transmitter power . 11
5.3.3 Maximum permissible frequency deviation . 11
ETSI
4 Final draft ETSI EN 300 433-2 V1.3.1 (2011-05)
5.3.4 Adjacent channels power . 11
5.3.5 Unwanted emissions in the spurious domain . 11
5.3.6 Transient behaviour of the transmitter . 11
5.3.7 Receiver spurious radiations . 11
Annex A (normative): HS Requirement and conformance Test specifications Table
(HS-RTT) . 12
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17

ETSI
5 Final draft ETSI EN 300 433-2 V1.3.1 (2011-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonised Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.2] are summarised in annex A.
The present document is part 2 of a multi-part deliverable covering Citizens' Band (CB) radio equipment, as identified
below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Significant changes from the previous version of the harmonised standard are: the standard includes angle modulated
CB equipment and the adaption of maximum transmitter power levels.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
6 Final draft ETSI EN 300 433-2 V1.3.1 (2011-05)
1 Scope
The present document covers the technical requirements for transmitters and receivers used in stations of angle
modulated, Double Side Band (DSB) modulated and/or Single Side Band (SSB) modulated Citizens' Band (CB) radio
equipment operating in all or part of the frequency band 26,960 MHz to 27,410 MHz with a channel spacing of 10 kHz,
and intended for analogue speech and/or data transmission.
Citizens' Band radio equipment operation is in accordance with Draft ECC Decision on the harmonised use of
frequencies for Citizens' Band (CB) radio equipment [i.5].
The equipment operates on one or more channels of the carrier frequencies as shown in table 1.
Table 1: Carrier frequencies
Carrier Channel Carrier frequencies Channel
frequencies Number Number
26,965 MHz 1 27,215 MHz 21
26,975 MHz 2 27,225 MHz 22
26,985 MHz 3 27,235 MHz 24
27,005 MHz 4 27,245 MHz 25
27,015 MHz 5 27,255 MHz 23
27,025 MHz 6 27,265 MHz 26
27,035 MHz 7 27,275 MHz 27
27,055 MHz 8 27,285 MHz 28
27,065 MHz 9 27,295 MHz 29
27,075 MHz 10 27,305 MHz 30
27,085 MHz 11 27,315 MHz 31
27,105 MHz 12 27,325 MHz 32
27,115 MHz 13 27,335 MHz 33
27,125 MHz 14 27,345 MHz 34
27,433 MHz 15 27,355 MHz 35
27,155 MHz 16 27,365 MHz 36
27,165 MHz 17 27,375 MHz 37
27,175 MHz 18 27,385 MHz 38
27,185 MHz 19 27,395 MHz 39
27,205 MHz 20 27,405 MHz 40
Transmission and reception takes place on the same channel (single frequency simplex mode).
Any equipment using national regulations on Citizens' Band (CB) permitting the use of channels outside of the carrier
frequencies shown in table 1 within the frequency range from 26 MHz to 28 MHz can use the present document.
The types of equipment covered by the present document are as follows:
- Base st
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Citizens' Band (CB) radio equipment - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 300 433-2 Version 1.3.1SIST EN 300 433-2 V1.3.1:2011en01-september-2011SIST EN 300 433-2 V1.3.1:2011SLOVENSKI
STANDARD
ETSI ETSI EN 300 433-2 V1.3.1 (2011-07) 2
Reference REN/ERM-TGDMR-266-2 Keywords CB, radio, regulation, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 433-2 V1.3.1:2011

ETSI ETSI EN 300 433-2 V1.3.1 (2011-07) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Introduction . 5 1 Scope . 6 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 8 3.3 Abbreviations . 8 4 Technical requirements . 8 4.1 Environmental profile . 8 4.2 Transmitter requirements . 8 4.2.1 Frequency error . 8 4.2.1.1 Definition . 8 4.2.1.2 Limit . 8 4.2.1.3 Conformance . 8 4.2.2 Transmitter power . 8 4.2.2.1 Definition . 8 4.2.2.2 Limit . 8 4.2.2.3 Conformance . 9 4.2.3 Maximum permissible frequency deviation . 9 4.2.3.1 Definition . 9 4.2.3.2 Limit . 9 4.2.3.3 Conformance . 9 4.2.4 Adjacent channel power . 9 4.2.4.1 Definition . 9 4.2.4.2 Limit . 9 4.2.4.3 Conformance . 9 4.2.5 Unwanted emissions in the spurious domain . 9 4.2.5.1 Definition . 9 4.2.5.2 Limits . 9 4.2.5.3 Conformance . 9 4.2.6 Transient behaviour of the transmitter . 9 4.2.6.1 Definition . 9 4.2.6.2 Limits . 9 4.2.6.3 Conformance . 10 4.3 Receiver requirements . 10 4.3.1 Spurious radiations . 10 4.3.1.1 Definition . 10 4.3.1.2 Limits . 10 4.3.1.3 Conformance . 10 5 Testing for compliance with technical requirements . 10 5.1 Environmental conditions for testing . 10 5.1.1 Normal and extreme test-conditions . 10 5.1.2 Test power source . 10 5.1.3 Choice of samples for the measurements . 10 5.2 Interpretation of the measurement results . 10 5.3 Essential test suites . 11 5.3.1 Frequency error . 11 5.3.2 Transmitter power . 11 5.3.3 Maximum permissible frequency deviation . 11 SIST EN 300 433-2 V1.3.1:2011

ETSI ETSI EN 300 433-2 V1.3.1 (2011-07) 4 5.3.4 Adjacent channels power . 11 5.3.5 Unwanted emissions in the spurious domain . 11 5.3.6 Transient behaviour of the transmitter . 11 5.3.7 Receiver spurious radiations . 11 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 12 Annex B (informative): The EN title in the official languages . 14 Annex C (informative): Bibliography . 15 History . 16
ETSI ETSI EN 300 433-2 V1.3.1 (2011-07) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarised in annex A. The present document is part 2 of a multi-part deliverable covering Citizens' Band (CB) radio equipment, as identified below: Part 1: "Technical characteristics and methods of measurement"; Part 2:
"Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive". Significant changes from the previous version of the harmonised standard are: the standard includes angle modulated CB equipment and the adaption of maximum transmitter power levels.
National transposition dates Date of adoption of this EN: 5 July 2011 Date of latest announcement of this EN (doa): 31 October 2011 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 April 2012 Date of withdrawal of any conflicting National Standard (dow): 30 April 2013
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 300 433-2 V1.3.1:2011

ETSI ETSI EN 300 433-2 V1.3.1 (2011-07) 6 1 Scope The present document covers the technical requirements for transmitters and receivers used in stations of angle modulated, Double Side Band (DSB) modulated and/or Single Side Band (SSB) modulated Citizens' Band (CB) radio equipment operating in all or part of the frequency band 26,960 MHz to 27,410 MHz with a channel spacing of 10 kHz, and intended for analogue speech and/or data transmission. Citizens' Band radio equipment operation is in accordance with Draft ECC Decision on the harmonised use of frequencies for Citizens' Band (CB) radio equipment [i.5]. The equipment operates on one or more channels of the carrier frequencies as shown in table 1. Table 1: Carrier frequencies Carrier frequencies Channel Number Carrier frequencies Channel Number 26,965 MHz 1 27,215 MHz 21 26,975 MHz 2 27,225 MHz 22 26,985 MHz 3 27,235 MHz 24 27,005 MHz 4 27,245 MHz 25 27,015 MHz 5 27,255 MHz 23 27,025 MHz 6 27,265 MHz 26 27,035 MHz 7 27,275 MHz 27 27,055 MHz 8 27,285 MHz 28 27,065 MHz 9 27,295 MHz 29 27,075 MHz 10 27,305 MHz 30 27,085 MHz 11 27,315 MHz 31 27,105 MHz 12 27,325 MHz 32 27,115 MHz 13 27,335 MHz 33 27,125 MHz 14 27,345 MHz 34 27,433 MHz 15 27,355 MHz 35 27,155 MHz 16 27,365 MHz 36 27,165 MHz 17 27,375 MHz 37 2
...