SIST EN 13523-21:2004
(Main)Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels
Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels
This Part of this European Standard specifies the procedure for evaluating the behaviour of an organic coating on a metallic substrate during and after outdoor exposure. Panel design, preparation and the procedure for outdoor exposure are to be performed in accordance with EN 13523-19.
After washing of the panel some dirt can remain on the panel. This remaining dirt can influence the accuracy and precision of readings of gloss and colour, performed on exposed panels, although carried out in accordance with the standards. Unlike other precise measurements, the objective of this Part of this European Standard is to report on trends in the corrosion and/or paint degradation behaviour of coil coated panels.
Bandbeschichtete Metalle - Prüfverfahren - Teil 21: Bewertung von freibewitterten Probenplatten
Dieser Teil dieser Europäischen Norm legt das Bewerten einer organischen Beschichtung auf einem metallischen Substrat während oder nach einer Freibewitterung fest. Die Maße der Probenplatte, Vorbereitung und Durchführung der Freibewitterung müssen PREN 13523-19 entsprechen.
Nach dem Waschen der Probenplatten kann etwas Schmutz auf der Probenplatte verbleiben. Bei Glanz- und Farbmessungen an bewitterten Platten, obwohl normgerecht durchgeführt, ist deshalb nicht die gleiche Genauigkeit und Präzision sichergestellt. Im Unterschied zu anderen genauen Messungen soll dieser Teil dieser Europäischen Norm Tendenzen im Korrosions- und Abbauverhalten von Beschichtungen auf bandbeschichteten Platten ermitteln.
Tôles prélaquées - Méthodes d'essai - Partie 21 : Evaluation des panneaux exposés en extérieur
La présente partie de la Norme européenne décrit le mode opératoire pour évaluer le comportement d'un revêtement organique sur un subjectile métallique durant et après exposition à l'extérieur. La conception des panneaux, la préparation et le mode opératoire d'exposition à l'extérieur sont à réaliser conformément au prEN 13523-19.
Après lavage du panneau, il est possible que toute la saleté ne soit pas éliminée. La saleté qui subsiste peut influer sur la précision et la fidélité des lectures du brillant et de la couleur réalisées sur les panneaux exposés, même si celles-ci sont effectuées conformément aux normes. Contrairement à d'autres mesures fidèles, le but de la présente partie de cette norme européenne est de faire rapport sur les tendances observées concernant le comportement à la corrosion et ou à la dégradation de la peinture des panneaux prélaqués.
Kovine, zaščitene po postopku coil-coating – Preskusne metode – 21. del: Ovrednotenje preskušancev, izpostavljenih zunanjemu okolju
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 21: Bewertung von freibewitterten ProbenplattenTôles prélaquées - Méthodes d'essai - Partie 21 : Evaluation des panneaux exposés en extérieurCoil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-21:2003SIST EN 13523-21:2004en01-januar-2004SIST EN 13523-21:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13523-21August 2003ICS 17.040.20; 25.220.60English versionCoil coated metals - Test methods - Part 21: Evaluation ofoutdoor exposed panelsTôles prélaquées - Méthodes d'essai - Partie 21 :Evaluation des panneaux exposés en extérieurBandbeschichtete Metalle - Prüfverfahren - Teil 21:Bewertung von freibewitterten ProbenplattenThis European Standard was approved by CEN on 10 July 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13523-21:2003 ESIST EN 13523-21:2004
6 to 7)in water.5.5Cloth or sponge, non-abrasive and smooth.6 SamplingSee EN 13523-0.7 Test panelsSee EN 13523-0.8 Procedure8.1 GeneralEvaluate the coating properties at ambient temperature.It is recommended that the panels are inspected not less than every six months in the first year and yearly afterwards.Colour measurements on metallics as well as gloss and colour measurements on textured and embossed surfaces areonly indicative.SIST EN 13523-21:2004
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.