ISO 15065:2005
(Main)Countersinks for countersunk head screws with head configuration in accordance with ISO 7721
Countersinks for countersunk head screws with head configuration in accordance with ISO 7721
ISO 15065:2005 specifies the dimensions and designation of countersinks for countersunk head screws with a head configuration in accordance with ISO 7721. It is applicable to the types of screws according to ISO 2009, ISO 2010, ISO 1482, ISO 1483, ISO 7046-1 and ISO 7046-2, ISO 7047, ISO 7050, ISO 7051, ISO 15482, ISO 15483, ISO 14584, ISO 14586, and ISO 14587.
Fraisures pour vis à tête fraisée avec une configuration de la tête conforme à l'ISO 7721
L'ISO 15065:2005 spécifie les dimensions et la désignation des fraisures pour vis à tête fraisée avec une configuration de la tête conforme à l'ISO 7721. À ce jour, l'ISO 15065:2005 s'applique aux types de vis conformes à l'ISO 1482, à l'ISO 1483, à l'ISO 2009, à l'ISO 2010, à l'ISO 7046-1, à l'ISO 7046-2, à l'ISO 7047, à l'ISO 7050, à l'ISO 7051, à l'ISO 14584, à l'ISO 14586, à l'ISO 14587, à l'ISO 15482 et à l'ISO 15483.
General Information
- Status
- Published
- Publication Date
- 09-Feb-2005
- Technical Committee
- ISO/TC 2/SC 7 - Reference standards
- Drafting Committee
- ISO/TC 2/SC 7 - Reference standards
- Current Stage
- 9093 - International Standard confirmed
- Start Date
- 19-Jun-2023
- Completion Date
- 21-Mar-2026
Relations
- Effective Date
- 12-Feb-2026
Overview
ISO 15065:2005 is an international standard developed by the International Organization for Standardization (ISO), specifying the dimensions and designation for countersinks used with countersunk head screws that conform to the head configuration detailed in ISO 7721. This standard ensures a unified approach to the manufacture and application of countersinks, promoting interchangeability and consistency across a wide range of mechanical and engineering projects.
ISO 15065:2005 applies to various screw types covered by numerous ISO standards, including both slotted and cross-recessed countersunk screws, raised head screws, tapping screws, and hexalobular socket screws. Compliance with this standard supports the reliable assembly of components where flush fitting of screw heads is required for functional or aesthetic reasons.
Key Topics
- Scope and Purpose: Specifies the dimensions and designation of countersinks compatible with the head configurations of countersunk screws as per ISO 7721.
- Screw Types Covered: The standard applies to slotted, cross-recessed, and hexalobular socket countersunk head screws, including varieties for tapping and drilling.
- Reference Standards: Aligns with related ISO standards such as ISO 2009, ISO 2010, ISO 1482, ISO 7046, ISO 7047, ISO 7050, ISO 14584, ISO 14586, and ISO 14587.
- Dimensional Requirements: Provides unified dimensions for countersinks to ensure compatibility and interchangeability between screws and receiving hardware.
- Designation System: Outlines a clear nomenclature for identifying countersinks by their nominal size and conformity to ISO 7721.
Applications
ISO 15065:2005 is vital in any industry where secure and flush fastening with countersunk screws is critical. Common applications include:
- Mechanical Engineering: Ensures reliable, flush mounts of machine components, reducing snag points and improving aesthetics.
- Automotive and Aerospace: Used where precision fastener seating enhances safety, structural integrity, and appearance.
- Electronics Assembly: Allows for the neat mounting of circuit boards and panels with screws that sit flush with surfaces.
- Construction and Fabrication: Supports consistent fastening of metal, wood, and composite materials where countersunk fasteners are preferred.
- General Manufacturing: Facilitates the mass production of parts, ensuring that different manufacturers' components fit together seamlessly.
Implementing countersinks as specified by this standard improves assembly efficiency, enhances product quality, and reduces the risk of improper fastener seating that could compromise the integrity of the finished assembly.
Related Standards
A number of ISO standards are closely linked to ISO 15065:2005 for countersink and countersunk head screw applications:
- ISO 7721: Defines the head configuration and gauging for countersunk head screws.
- ISO 273: Specifies clearance holes for bolts and screws.
- ISO 2009, ISO 2010: Pertains to slotted countersunk head screws.
- ISO 1482, ISO 1483: Covers slotted tapping screws.
- ISO 7046-1, ISO 7046-2, ISO 7047, ISO 7050, ISO 7051: Address cross-recessed countersunk screws.
- ISO 14584, ISO 14586, ISO 14587: Focus on hexalobular socket countersunk screws.
- ISO 15482, ISO 15483: Relate to cross-recessed countersunk drilling screws.
Adhering to ISO 15065:2005 and these associated standards is essential for engineers, manufacturers, and designers aiming for global compatibility and optimal performance in products utilizing countersunk fasteners.
Buy Documents
ISO 15065:2005 - Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 Released:2/10/2005
ISO 15065:2005 - Fraisures pour vis a tete fraisée avec une configuration de la tete conforme a l'ISO 7721 Released:2/10/2005
Frequently Asked Questions
ISO 15065:2005 is a standard published by the International Organization for Standardization (ISO). Its full title is "Countersinks for countersunk head screws with head configuration in accordance with ISO 7721". This standard covers: ISO 15065:2005 specifies the dimensions and designation of countersinks for countersunk head screws with a head configuration in accordance with ISO 7721. It is applicable to the types of screws according to ISO 2009, ISO 2010, ISO 1482, ISO 1483, ISO 7046-1 and ISO 7046-2, ISO 7047, ISO 7050, ISO 7051, ISO 15482, ISO 15483, ISO 14584, ISO 14586, and ISO 14587.
ISO 15065:2005 specifies the dimensions and designation of countersinks for countersunk head screws with a head configuration in accordance with ISO 7721. It is applicable to the types of screws according to ISO 2009, ISO 2010, ISO 1482, ISO 1483, ISO 7046-1 and ISO 7046-2, ISO 7047, ISO 7050, ISO 7051, ISO 15482, ISO 15483, ISO 14584, ISO 14586, and ISO 14587.
ISO 15065:2005 is classified under the following ICS (International Classification for Standards) categories: 21.060.10 - Bolts, screws, studs. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 15065:2005 has the following relationships with other standards: It is inter standard links to EN ISO 15065:2005. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ISO 15065:2005 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 15065
First edition
2005-02-15
Countersinks for countersunk head
screws with head configuration in
accordance with ISO 7721
Fraisures pour vis à tête fraisée avec une configuration de la tête
conforme à l'ISO 7721
Reference number
©
ISO 2005
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15065 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 7, Reference
Standards for fasteners (mainly covering terminology, dimensioning, sizes and tolerancing).
INTERNATIONAL STANDARD ISO 15065:2005(E)
Countersinks for countersunk head screws with head
configuration in accordance with ISO 7721
1 Scope
This International Standard specifies the dimensions and designation of countersinks for countersunk head
screws with a head configuration in accordance with ISO 7721.
This International Standard is applicable to the following types of screws:
slotted countersunk flat head screws according to ISO 2009;
slotted countersunk raised head screws according to ISO 2010;
slotted countersunk flat head tapping screws according to ISO 1482;
slotted countersunk raised head tapping screws according to ISO 1483;
cross-recessed countersunk flat head screws according to ISO 7046-1 and ISO 7046-2;
cross-recessed countersunk raised head screws according to ISO 7047;
cross-recessed countersunk flat head tapping screws according to ISO 7050;
cross-recess
...
NORME ISO
INTERNATIONALE 15065
Première édition
2005-02-15
Fraisures pour vis à tête fraisée avec
une configuration de la tête conforme
à l'ISO 7721
Countersinks for countersunk head screws with head configuration in
accordance with ISO 7721
Numéro de référence
©
ISO 2005
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2005
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2005 – Tous droits réservés
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 15065 a été élaborée par le comité technique ISO/TC 2, Éléments de fixation, sous-comité SC 7,
Normes de référence pour éléments de fixation (essentiellement la terminologie, les dimensions générales et
le tolérancement).
NORME INTERNATIONALE ISO 15065:2005(F)
Fraisures pour vis à tête fraisée avec une configuration de la
tête conforme à l'ISO 7721
1 Domaine d'application
La présente Norme internationale spécifie les dimensions et la désignation des fraisures pour vis à tête
fraisée avec une configuration de la tête conforme à l'ISO 7721.
À ce jour, la présente Norme internationale s'applique aux types de vis suivants:
vis à métaux à tête fraisée fendue selon l'ISO 2009
vis à métaux à tête fraisée bombée fendue selon l'ISO 2010
vis à tôle à tête fraisée, fendue selon l'ISO 1482
vis à tôle à tête fraisée bombée, fendue selon l'ISO
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...