ISO/IEC 10373-1:2020
(Main)Cards and security devices for personal identification — Test methods — Part 1: General characteristics
Cards and security devices for personal identification — Test methods — Part 1: General characteristics
This document describes the test methods for characteristics of identification cards according to ISO/IEC 7810 and other standards, such as those listed in the Introduction. NOTE 1 Criteria for acceptability do not form part of this document but are found in other International Standards including those mentioned in the introduction. NOTE 2 Test methods described in this document are intended to be performed separately. A given card is not required to pass through all the tests sequentially.
Cartes et dispositifs de sécurité pour l'identification personnelle — Méthodes d'essai — Partie 1: Caractéristiques générales
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 10373-1
Third edition
2020-10
Cards and security devices for
personal identification — Test
methods —
Part 1:
General characteristics
Cartes et dispositifs de sécurité pour l'identification personnelle —
Méthodes d'essai —
Partie 1: Caractéristiques générales
Reference number
©
ISO/IEC 2020
© ISO/IEC 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO/IEC 2020 – All rights reserved
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
3.1 Terms and definitions . 1
3.2 Abbreviated terms . 3
4 Default items applicable to the test methods . 3
4.1 Test environment . 3
4.2 Pre-conditioning . 3
4.3 Selection of test methods . 3
4.4 Default tolerance . 4
4.5 Total measurement uncertainty . 4
5 Test methods . 4
5.1 Card warpage . 4
5.1.1 General. 4
5.1.2 Apparatus . 4
5.1.3 Procedure . 4
5.1.4 Test report . 5
5.2 Dimensions of cards . 5
5.2.1 General. 5
5.2.2 Thickness of card measurements . 5
5.2.3 Height and width of card measurement . 6
5.3 Peel strength . 6
5.3.1 General. 6
5.3.2 Apparatus . 7
5.3.3 Procedure . 7
5.3.4 Test report . 9
5.4 Peel strength including the edge of the card . 9
5.4.1 General. 9
5.4.2 Apparatus . 9
5.4.3 Procedure .11
5.4.4 Test report .14
5.5 Resistance to chemicals .14
5.5.1 General.14
5.5.2 Reagents .14
5.5.3 Procedure .17
5.5.4 Test report .18
5.6 Card dimensional stability and warpage with temperature and humidity .18
5.6.1 General.18
5.6.2 Procedure .18
5.6.3 Test report .18
5.7 Adhesion or blocking .19
5.7.1 General.19
5.7.2 Procedure .19
5.7.3 Test report .19
5.8 Bending stiffness .19
5.8.1 General.19
5.8.2 Procedure .19
5.8.3 Test report .21
5.9 Dynamic bending stress .21
5.9.1 General.21
© ISO/IEC 2020 – All rights reserved iii
5.9.2 Apparatus .21
5.9.3 Calibration method .23
5.9.4 Procedure .23
5.9.5 Test report .24
5.10 Dynamic torsional stress .25
5.10.1 General.25
5.10.2 Apparatus .25
5.10.3 Procedure .25
5.10.4 Test report .26
5.11 Opacity .26
5.11.1 General.26
5.11.2 Apparatus .26
5.11.3 Procedure .28
5.12 X-rays .29
5.12.1 General.29
5.12.2 Procedure .29
5.12.3 Test report .29
5.13 Embossing relief height of characters .29
5.13.1 General.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.