ISO 23316-7:2023

INTERNATIONAL ISO
STANDARD 23316-7
First edition
2023-08
Tractors and machinery for
agriculture and forestry — Electrical
high-power interface 700 V DC / 480 V
AC —
Part 7:
Mechanical integration
Reference number
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Mounting positions at tractor and implement . 1
4.1 Rear mounted implements . . 1
4.2 Front mounted implements . . 2
5 Cabling . 3
5.1 Cabling on tractor side. 3
5.2 Cabling on implement side . 3
5.2.1 Implement cable length . 3
5.2.2 Maximum length of free hanging cable . 3
5.2.3 Maximum pull force of cable . 3
5.2.4 Environmental conditions . 4
5.2.5 Cable support and clamp location . 4
5.2.6 Strain relief . 4
6 Park box for connector .4
Bibliography . 5
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had received notice of
(a) patent(s) which may be required to implement this document. However, implementers are cautioned
that this may not represent the latest information, which may be obtained from the patent database
available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent
rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture
and forestry, Subcommittee SC 19, Agricultural electronics.
A list of all parts in the ISO 23316 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
The purpose of the ISO 23316 series is to provide design and application standards covering
implementation of electrical high power interface with a nominal voltage of 700 VDC/480 VAC for
agricultural and forestry machinery.
Conformance to the ISO 23316 series is determined when applicable requirements from all parts of the
ISO 23316 series are met.
It is permitted for partial systems or components to be compliant to the ISO 23316 series by applying
all applicable requirements, e.g. for the plug, receptacle or inverters, on a tractor or implement.
NOTE For example, if a DC-mode only HPI is provided, it is not necessary to comply with ISO 23316-4
describing AC-mode, as it is not applicable. If an AC-mode only HPI is provided, it is not necessary to comply with
ISO 23316-5 describing DC-mode, as it is not applicable.
The ISO 23316 series specifies physical and logical interface requirements that provide interoperability
and cross compatibility for systems and equipment operating at nominal voltages of 700 VDC/480 VAC.
The following are not within the scope of the ISO 23316 series:
— service, maintenance, and related diagnostics;
— functional safety;
— control strategies for high power sources and loads;
— application-specific strategies and operational modes;
— component design;
— energy storage systems, e.g. supercapacitors or batteries;
— multiple electrical power sources supplying a common DC link.
ISO 23316-1 describes the general purpose and structure of standards in the ISO 23316 series.
v
© ISO
...