Status
Not Published
Current Stage
5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
Start Date
16-Nov-2026
Completion Date
16-Nov-2026

Buy Documents

Draft

ISO/FDIS 11670 - Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability

Release Date:02-Nov-2026
English language (11 pages)
sale 15% off
sale 15% off
Draft

REDLINE ISO/FDIS 11670 - Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability

Release Date:02-Nov-2026
English language (11 pages)
sale 15% off
sale 15% off

ISO/FDIS 11670 is an ISO draft standard on test methods for laser beam parameters, focused on beam spatial stability. It specifies methods for determining laser beam positional stability and angular stability, so users can characterize how much a beam moves sideways and how much its direction changes over time. The document is intended for testing and characterization of lasers and laser-related equipment.

What does ISO/FDIS 11670 specify?

ISO/FDIS 11670 specifies how to measure laser beam positional stability and angular stability in a laboratory setting. The document explains the coordinate system, the test principles, the measurement arrangement, the evaluation steps, and the test report content.

The standard is organized into clauses covering scope, normative references, terms and definitions, coordinate system, test principles, measurement arrangement and auxiliary devices, test procedures, evaluation, and test report. In practice, that structure takes the reader from setup to calculation to documentation.

What are the key requirements of ISO/FDIS 11670?

Position stability

ISO/FDIS 11670 measures position fluctuation widths from repeated beam centroid coordinates at a fixed location. The beam centroid is obtained from the irradiance or fluence distribution, or from an equivalent lateral-position detector, and the set of momentary coordinates is used to calculate mean position and deviation width.

For users, this means the test is not a single spot measurement - it is a time-based stability measurement. The document requires at least 1 000 samples over the chosen interval, and the result can be reported for short-term, medium-term, or long-term stability.

Angular stability

ISO/FDIS 11670 measures angular fluctuation widths indirectly in the focal plane of a focusing element placed downstream of the measurement plane. The measured position fluctuation widths in that focal plane are divided by the focal length to obtain angular fluctuation widths.

This matters because beam direction is not measured directly by angle sensors in the core method. Instead, the user needs a known focusing element and a correctly located detector plane, so the geometry of the setup becomes part of the result.

Coordinate system and setup

ISO/FDIS 11670 requires the z-axis to follow the beam propagation direction approximately, while the transverse X- and Y-axes must be specified. The z location of the measurement plane must be stated because results can depend on where the beam is measured.

The setup also has practical alignment rules. The laser beam and measurement axis shall be coaxial, optical components shall be centered on the axis, and clipping losses should stay below 1%. This reduces false stability errors caused by the test arrangement itself.

Environment and detector system

ISO/FDIS 11670 requires thermal equilibrium of both the laser and the test equipment before measurement. It also calls for measures against reflections, ambient and thermal radiation, air turbulence, thermal blooming, mechanical noise, and temperature drift.

For the detector system, the standard points users to ISO 11146-1 and allows CCD or CMOS cameras, lateral effect position sensors, quadrant photodiodes, or similar devices if equivalent results are demonstrated. It also requires calibration of detector sensitivity to lateral beam displacement before measuring position fluctuation width.

Evaluation and reporting

ISO/FDIS 11670 defines the calculation path from centroid coordinates to deviations and then to fluctuation widths. If imaging optics are used, the result must be corrected by the magnification factor; for angular measurements, the focal length correction is applied.

The test report must capture the laser identity, wavelength, operating mode, key operating settings, detector and sampling details, optical components used, the reference plane and axis, the results for position and angular stability, and any deviations or unusual observations. In practice, this makes results traceable and comparable.

What terms does ISO/FDIS 11670 define?

  • Beam spatial stability - the combined positional and angular stability of a laser beam.
  • Momentary beam centroid coordinates - the centroid coordinates of the beam measured at one moment at a given location.
  • Position fluctuation widths - numerical measures of how widely the beam centroid position varies over time.
  • Angular fluctuation widths - numerical measures of how widely the beam direction varies over time.
  • Beam spatial change from cold start - the difference between the initial beam position/direction after switch-on and the later stabilized state after warm-up.
  • Short-term spatial fluctuation width - spatial fluctuation measured within 1 s.
  • Medium-term spatial fluctuation width - spatial fluctuation measured within 1 min.
  • Long-term spatial fluctuation width - spatial fluctuation measured within 1 h.

Who uses ISO/FDIS 11670?

ISO/FDIS 11670 is used by laser manufacturers, test laboratories, and organizations that evaluate or characterize lasers. Quality managers and buyers can use it when they need a repeatable way to compare beam stability across products or production batches.

It is most relevant in optics and photonics, where beam movement and beam steering affect alignment, energy delivery, and measurement repeatability. It also supports technical reporting when a laser must be documented against a defined test method.

What changed in ISO/FDIS 11670 from the previous edition?

ISO/FDIS 11670 is the third edition and replaces ISO 11670:2003, including its Technical Corrigendum ISO 11670:2003/Cor.1:2004. The foreword states that the title, terms and definitions, and main text were revised from “beam positional stability” to “beam spatial stability”.

The foreword also states that rarely used terms and definitions were removed, new Figures 1 to 3 were included, the normative references were updated, and Annexes A and B were removed.

Which standards are used with ISO/FDIS 11670?

  • ISO 11145 - provides vocabulary and symbols used alongside the beam terminology in this document.
  • ISO 11146-1 - provides the beam-width, divergence-angle, and beam propagation ratio methods that the detector and moment calculations rely on.
  • IEC 61040 - supplies reference material for power and energy measuring detectors, instruments, and equipment for laser radiation.

What does the ISO/FDIS 11670 document contain?

ISO/FDIS 11670 contains the definitions and calculation basis for beam centroid position, beam direction, displacement distributions, and fluctuation widths. It also gives the coordinate system and the practical test principles for direct position measurement, indirect position measurement through imaging optics, and angular measurement through a focusing element.

The document includes three figures showing the direct position setup, the imaging-based position setup, and the angular setup. It also includes the evaluation sequence for converting measured coordinates into reported stability values.

The test report clause provides a structured checklist for what to record: laser identity, operating conditions, detector and sampling details, optical components, measurement reference choices, results, deviations, and unusual features.

Relations

Effective Date
12-Feb-2026
Effective Date
28-Oct-2023
Effective Date
06-Jun-2022

Buy Documents

Draft

ISO/FDIS 11670 - Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability

Release Date:02-Nov-2026
English language (11 pages)
sale 15% off
sale 15% off
Draft

REDLINE ISO/FDIS 11670 - Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability

Release Date:02-Nov-2026
English language (11 pages)
sale 15% off
sale 15% off

Frequently Asked Questions

ISO/FDIS 11670 is a draft published by the International Organization for Standardization (ISO). Its full title is "Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability". This standard covers: Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability

Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability

ISO/FDIS 11670 is classified under the following ICS (International Classification for Standards) categories: 31.260 - Optoelectronics. Laser equipment. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO/FDIS 11670 has the following relationships with other standards: It is inter standard links to FprEN ISO 11670, ISO 10191:2021, ISO 11670:2003. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ISO/FDIS 11670 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


FINAL DRAFT
International
Standard
ISO/TC 172/SC 9
Lasers and laser-related
Secretariat: DIN
equipment — Test methods for
Voting begins on:
laser beam parameters — Beam
2026-11-16
spatial stability
Voting terminates on:
2026-12-28
Lasers et équipements associés aux lasers — Méthodes d'essai des
paramètres du faisceau laser — Stabilité de visée du faisceau
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
FINAL DRAFT
International
Standard
ISO/TC 172/SC 9
Lasers and laser-related
Secretariat: DIN
equipment — Test methods for
Voting begins on:
laser beam parameters — Beam
spatial stability
Voting terminates on:
Lasers et équipements associés aux lasers — Méthodes d'essai des
paramètres du faisceau laser — Stabilité de visée du faisceau
© ISO 2026
All rights reserved.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
an ISO member body, or an authorized third-party distributor.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
photocopying, scanning, recording, or posting on internal or external digital platforms. TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
Reference number
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Coordinate system . 5
5 Test principles . 5
5.1 Position fluctuation widths .5
5.2 Angular fluctuation widths .5
6 Measurement arrangement, test equipment and auxiliary devices . 6
6.1 Preparation .6
6.2 Control of environment .6
6.3 Detection system .6
6.4 Optical attenuators, beam splitters, imaging optics, focusing elements .6
6.5 Calibration of detector sensitivity to lateral beam displacement .7
7 Test procedures . 7
7.1 General .7
7.2 Position fluctuation widths .7
7.3 Angular fluctuation widths .8
8 Evaluation . 9
8.1 Position fluctuation widths .9
8.2 Angular fluctuation widths .9
9 Test report .10

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9,
Laser and electro-optical systems, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 123, Lasers and photonics, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 11670:2003), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 11670:2003/Cor.1:2004.
The main changes are as follows:
— title, terms and definitions and main text were revised from “beam positional stability” to using the new
term “beam spatial stability”
— rarely used terms and definitions have been removed;
— new Figures 1 to 3 were included;
— standard was updated to new normative references;
— Annexes A and B have been removed.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
Introduction
The centre of a laser beam in a plane perpendicular to the direction of propagation is defined as the centroid
or first-order spatial moment of the irradiance (fluence) distribution. The current propagation axis of a
beam is then the straight line connecting two centroids measured at two different planes simultaneously
in a uniform, homogeneous medium. Beam axis instabilities may be characterized by transverse position
displacements and by angular direction displacements that are either monotonic, periodic, or stochastic in
time.
The magnitude of the transverse position fluctuations in a plane is quantified by the position displacement
width. A smaller RMS position displacement width is equivalent to greater beam positional stability.
The magnitude of the angular fluctuations in a plane is quantified by the angular fluctuation width. A smaller
RMS angular fluctuation width is equivalent to greater beam directional stability.
If the magnitude of the transverse fluctuations in an application plane is not significantly smaller than the
(instantaneous) beam diameter there, then, at longer exposure times, the laser radiation will be distributed
over a larger area as would be expected based on the beam diameter alone, leading to an increased effective
beam diameter and reducing the time-averaged energy density.
In the same manner angular fluctuations can increase the effective divergence of a laser beam.
The positional stability of the beam and the angular stability of the beam are referred to together as the
spatial stability of the beam.
This document provides general principles for the measurement of the positional and angular beam stability.
In addition, definitions of terminology and symbols to be used in referring to them are provided.

v
FINAL DRAFT International Standard ISO/FDIS 11670:2026(en)
Lasers and laser-related equipment — Test methods for laser
beam parameters — Beam spatial stability
1 Scope
This document specifies methods for determining laser beam positional as well as angular stability. The test
methods given in this document are used for the testing and characterization of lasers.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 11145, Optics and photonics — Lasers and laser-related equipment — Vocabulary and symbols
ISO 11146-1, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles and
beam propagation ratios — Part 1: Stigmatic and simple astigmatic beams
1)
IEC 61040 , Power and energy measuring detectors, instruments and equipment for laser radiation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 11145, ISO 11146-1 and IEC 61040
and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
momentary beam centroid coordinates
xz , yz
 
first order moments of the momentary irradiance (fluence) of a fluctuating beam at location z measured
along the laboratory coordinates x and y of a beam propagating approximately in z direction
 xE xy,,zxddy

xz 

Ex,,yz ddxy

 yE xy,,zxddy

yz 

Ex,,yz ddxy

Note 1 to entry: In general, since fluctuations are assumed, the irradiance (fluence) distribution as well as the
momentary beam centroid coordinates vary from moment to moment (i.e. from measurement to measurement).
1)  Withdrawn.
3.2
distribution of momentary beam centroid coordinates
xz , yz
 
ii
set of momentary beam centroid coordinates (3.1) measured at different moments (times) at the same location
z
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
3.3
mean beam centroid coordinates
xz , yz
 
MM
arithmetical mean of a distribution of momentary beam centroid coordinates (3.2) at location z
N
xz  xz
 
M i

N
i1
N
yz  yz
 
M i

N
i1
Note 1 to entry: If the number of measurements N of each set is sufficiently large, different sets measured on the same
beam at the same location z result in approximately the same mean beam centroid coordinates. Thus, the mean beam
centroid coordinates may be considered as the (stable) beam centroid position at location z.
3.4
momentary position displacement
xz , yz
 
deviation of the momentary beam centroid coordinates (3.1) from the mean beam centroid coordinates (3.3) at
location z
xz xz xz
  
M
yz  yz  yz
  
M
3.5
position displacement distributions
xz , yz
 
ii
set of momentary position displacements (3.4) at location z
xz  xz xz
  
ii M
yz  yz  yz
  
ii M
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
Note 2 to entry: If the number of measurements N is large enough, two independently measured position displacement
distributions of the same beam measured at the same location z, will have approximal the same extent, although the
distributions may not be identical.

3.6
position fluctuation widths
xz , yz
 
quantitative measures for the extent of a measured position displacement distribution at location z
N
xz

i

i1
xz 4

N1
N
yz

i

i1
y z 4

N1
Note 1 to entry: In general, the position fluctuation widths of a real beam will vary under free propagation through a
homogeneous medium. Thus, there will be indeed a dependency on the location z (in contrast to the angular fluctuation
width, see 3.12).
3.7
momentary beam direction angles
zz,
 
differential change in the beam centroid coordinates per propagation length of a fluctuating beam in a
certain moment at location z
xzzx z
 
 z  lim

z0 z
yzzy z
...


ISO /TC 172/SC 9/WG 1
Secretariat: DIN
Date: 2026-09-2910-30
Lasers and laser-related equipment — Test methods for laser
beam parameters — Beam spatial stability
This draft is submitted to a parallel vote in ISO, CEN.

© Lasers et équipements associés aux lasers — Méthodes d'essai des paramètres du faisceau laser — Stabilité
de visée du faisceau
FDIS stage
This draft is submitted to a parallel vote in ISO, CEN.
2 © ISO 2025 – All rights reserved

© ISO 2026
All rights reserved. Unless otherwise specified,
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued
by ISO, an ISO member body, or an authorized third-party distributor.
Except as required in the context of its for implementation or expressly permitted by a separate licence, no part of this
ISO publication may be reproduced or utilized otherwise, distributed, modified, used, or made available in any form or
by any means, – electronic or mechanical, including photocopying, scanning, recording, or posting on internal or external
digital platforms.
Any use beyond the internet or an intranet, without prior written permission. Permission can be requested from either
ISO at the address below or ISO’s member body in the countryscope of the requestergranted rights is prohibited and may
result in legal action.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
iii
Contents
Foreword . v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Coordinate system . 5
5 Test principles . 6
5.1 Position fluctuation widths . 6
5.2 Angular fluctuation widths . 6
6 Measurement arrangement, test equipment and auxiliary devices. 6
6.1 Preparation . 6
6.2 Control of environment . 7
6.3 Detection system . 7
6.4 Optical attenuators, beam splitters, imaging optics, focusing elements . 7
6.5 Calibration of detector sensitivity to lateral beam displacement . 8
7 Test procedures . 8
7.1 General . 8
7.2 Position fluctuation widths . 8
7.3 Angular fluctuation widths . 9
8 Evaluation . 10
8.1 Position fluctuation widths . 10
8.2 Angular fluctuation widths . 10
9 Test report . 11

iv
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9,
Laser and electro-optical systems, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 123, Lasers and photonics, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 11670:2003), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 11670:2003/Cor.1:2004.
The main changes are as follows:
— — title, terms and definitions and main text were revised from “beam positional stability” to using the
new term “beam spatial stability”
— — rarely used terms and definitions have been removed;
— — new Figures 1Figures 1 to 33 were included;
— — standard was updated to new normative references.;
— — Annexes A and B have been removed.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
Introduction
The centre of a laser beam in a plane perpendicular to the direction of propagation is defined as the centroid
or first-order spatial moment of the irradiance (fluence) distribution. The current propagation axis of a beam
is then the straight line connecting two centroids measured at two different planes simultaneously in a
uniform, homogeneous medium. Beam axis instabilities may be characterized by transverse position
displacements and by angular direction displacements that are either monotonic, periodic, or stochastic in
time.
The magnitude of the transverse position fluctuations in a plane is quantified by the position displacement
width. A smaller RMS position displacement width is equivalent to greater beam positional stability.
The magnitude of the angular fluctuations in a plane is quantified by the angular fluctuation width. A smaller
RMS angular fluctuation width is equivalent to greater beam directional stability.
If the magnitude of the transverse fluctuations in an application plane is not significantly smaller than the
(instantaneous) beam diameter there, then, at longer exposure times, the laser radiation will be distributed
over a larger area as would be expected based on the beam diameter alone, leading to an increased effective
beam diameter and reducing the time-averaged energy density.
In the same manner angular fluctuations can increase the effective divergence of a laser beam.
The positional stability of the beam and the angular stability of the beam are referred to together as the spatial
stability of the beam.
This document provides general principles for the measurement of the positional and angular beam stability.
In addition, definitions of terminology and symbols to be used in referring to them are provided.
vi
Lasers and laser-related equipment — Test methods for laser beam
parameters — Beam spatial stability
1 Scope
This document specifies methods for determining laser beam positional as well as angular stability. The test
methods given in this document are used for the testing and characterization of lasers.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 11145, Optics and photonics — Lasers and laser-related equipment — Vocabulary and symbols
ISO 11146--1, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles and
beam propagation ratios — Part 1: Stigmatic and simple astigmatic beams
1)
ENIEC 61040:1990, , Power and energy measuring detectors, instruments and equipment for laser radiation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 61040, ISO 11145 and, ISO 11146-
1 and IEC 61040 and the following apply.
ISO and IEC maintain terminologicalterminology databases for use in standardization at the following
addresses:
— — ISO Online browsing platform: available at https://www.iso.org/obp
— — IEC Electropedia: available at https://www.electropedia.org/
3.1 3.1
momentary beam centroid coordinates

𝑥𝑥¯(𝑧𝑧),𝑦𝑦¯(𝑧𝑧)
first order moments of the momentary irradiance (fluence) of a fluctuating beam at location z measured along
the laboratory coordinates x and y of a beam propagating approximately in z direction

∫∫𝑥𝑥⋅𝐸𝐸(𝑥𝑥,𝑦𝑦,𝑧𝑧)⋅ d𝑥𝑥 d𝑦𝑦
𝑥𝑥¯(𝑧𝑧) =
∫∫𝐸𝐸(𝑥𝑥,𝑦𝑦,𝑧𝑧)⋅ d𝑥𝑥 d𝑦𝑦
∫∫𝑦𝑦⋅𝐸𝐸(𝑥𝑥,𝑦𝑦,𝑧𝑧)⋅ d𝑥𝑥 d𝑦𝑦
𝑦𝑦¯(𝑧𝑧) =
∫∫𝐸𝐸(𝑥𝑥,𝑦𝑦,𝑧𝑧)⋅ d𝑥𝑥 d𝑦𝑦

1)
Withdrawn.
Note 1 to entry: In general, since fluctuations are assumed, the irradiance (fluence) distribution as well as the
momentary beam centroid coordinates vary from moment to moment (i.e.,. from measurement to measurement).
3.2 3.2
distribution of momentary beam centroid coordinates

𝑥𝑥¯ (𝑧𝑧),𝑦𝑦¯ (𝑧𝑧)
𝑖𝑖 𝑖𝑖
set of momentary beam centroid coordinates (3.1(3.1)) measured at different moments (times) at the same
location z
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
3.3 3.3
mean beam centroid coordinates

𝑥𝑥¯ (𝑧𝑧),𝑦𝑦¯ (𝑧𝑧)
M M
arithmetical mean of a distribution of momentary beam centroid coordinates (3.2(3.2)) at location z

𝑁𝑁
𝑥𝑥¯ (𝑧𝑧) = � 𝑥𝑥¯ (𝑧𝑧)
𝑀𝑀 𝑖𝑖
𝑁𝑁
𝑖𝑖=1
𝑁𝑁
𝑦𝑦¯ (𝑧𝑧) = � 𝑦𝑦¯ (𝑧𝑧)
𝑀𝑀 𝑖𝑖
𝑁𝑁
𝑖𝑖=1
Note 1 to entry: If the number of measurements N of each set is sufficiently large, different sets measured on the same
beam at the same location z result in approximately the same mean beam centroid coordinates. Thus, the mean beam
centroid coordinates may be considered as the (stable) beam centroid position at location z.
3.4 3.4
momentary position displacement

𝛿𝛿𝑥𝑥(𝑧𝑧), 𝛿𝛿𝑦𝑦(𝑧𝑧)
deviation of the momentary beam centroid coordinates (3.1(3.1)) from the mean beam centroid coordinates
(3.3(3.3)) at location z
3.5
𝛿𝛿𝑥𝑥(𝑧𝑧) =𝑥𝑥¯(𝑧𝑧)−𝑥𝑥¯ (𝑧𝑧)
𝑀𝑀
𝛿𝛿𝑦𝑦(𝑧𝑧) =𝑦𝑦¯(𝑧𝑧)−𝑦𝑦¯ (𝑧𝑧)
𝑀𝑀
3.5
position displacement distributions

𝛿𝛿𝑥𝑥 (𝑧𝑧), 𝛿𝛿𝑦𝑦 (𝑧𝑧)
𝑖𝑖 𝑖𝑖
set of momentary position displacements (3.4(3.4)) at location z

𝛿𝛿𝑥𝑥 (𝑧𝑧) =𝑥𝑥¯ (𝑧𝑧)−𝑥𝑥¯ (𝑧𝑧)
𝑖𝑖 𝑖𝑖 𝑀𝑀
𝛿𝛿𝑦𝑦 (𝑧𝑧) =𝑦𝑦¯ (𝑧𝑧)−𝑦𝑦¯ (𝑧𝑧)
𝑖𝑖 𝑖𝑖 𝑀𝑀
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
Note 2 to entry: If the number of measurements N is large enough, two independently measured position displacement
distributions of the same beam measured at the same location z, will have approximal the same extent, although the
distributions may not be identical.
3.53.6 3.6
position fluctuation widths
𝛥𝛥𝑥𝑥(𝑧𝑧), 𝛥𝛥𝑦𝑦(𝑧𝑧)
quantitative measures for the extent of a measured position displacement distribution at location z

𝑁𝑁 2
∑ 𝛿𝛿𝑥𝑥 (𝑧𝑧)
𝑖𝑖=1 𝑖𝑖
�
𝛥𝛥𝑥𝑥(𝑧𝑧) = 4
𝑁𝑁− 1
𝑁𝑁 2
∑ 𝛿𝛿𝑦𝑦 (𝑧𝑧)
𝑖𝑖=1 𝑖𝑖
�
𝛥𝛥y(𝑧𝑧) = 4
𝑁𝑁− 1
Note 1 to entry: In general, the position fluctuation widths of a real beam will vary under free propagation through a
homogeneous medium. Thus, there will be indeed a dependency on the location z (in contrast to the angular fluctuation
width, see 3.123.12).).
3.63.7 3.7
momentary beam direction angles

𝛼𝛼(𝑧𝑧), 𝛽𝛽(𝑧𝑧)
differential change in the beam centroid coordinates per propagation length of a fluctuating beam in a certain
moment at location z
𝑥𝑥¯(𝑧𝑧 +𝛥𝛥𝑧𝑧)−𝑥𝑥¯(𝑧𝑧)
𝛼𝛼(𝑧𝑧) = lim
𝛥𝛥𝛥𝛥→0
𝛥𝛥𝑧𝑧
𝑦𝑦¯(𝑧𝑧 +𝛥𝛥𝑧𝑧)−𝑦𝑦¯(𝑧𝑧)
𝛽𝛽(𝑧𝑧) = lim
𝛥𝛥𝛥𝛥→0
𝛥𝛥𝑧𝑧
Note 1 to entry: It is assumed that the beam propagates approximately in z direction.
Note 2 to entry: This is a formal definition of the beam direction angles. The practical measurement will be based on
another than this differential approach (see Clause 5Clause 5).).
Note 3 to entry: In general, since fluctuations are assumed, the momentary beam direction angles will vary from
moment to moment (i.e. from measurement to measurement).
3.73.8 3.8
distribution of momentary beam direction angles

𝛼𝛼 (𝑧𝑧), 𝛽𝛽 (𝑧𝑧)
𝑖𝑖 𝑖𝑖
set of momentary beam direction coordinates measured at different moments at the same location z.
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
3.83.9 3.9
mean beam direction angles
𝛼𝛼 (𝑧𝑧), 𝛽𝛽 (𝑧𝑧)
M M
arithmetical mean of a distribution of momentary beam direction angles (3.8(3.8))

𝑁𝑁
𝛼𝛼 (𝑧𝑧) = � 𝛼𝛼 (𝑧𝑧)
𝑀𝑀 𝑖𝑖
𝑁𝑁
𝑖𝑖=1
𝑁𝑁
𝛽𝛽 (𝑧𝑧) = � 𝛽𝛽 (𝑧𝑧)
𝑀𝑀 𝑖𝑖
𝑁𝑁
𝑖𝑖=1
Note 1 to entry: If the number of measurements N of each set is sufficiently large, different sets measured on the same
beam at the same location z will results in approximately the same mean beam direction angles. Thus, the mean beam
direction angles may be cons
...