ISO 13577-1:2016
(Main)Industrial furnaces and associated processing equipment — Safety — Part 1: General requirements
Industrial furnaces and associated processing equipment — Safety — Part 1: General requirements
ISO 13577-1:2016 the general safety requirements common to industrial furnaces and associated processing equipment (TPE). ISO 13577-1:2016 deals with the significant hazards, hazardous situations or hazardous events relevant to TPE, as listed in Annex A, when TPE is used as intended and also under conditions of misuse that are reasonably foreseeable by the manufacturer. Annex B provides a list of common industrial furnaces and associated processing equipment. This document specifies the requirements intended to be met by the manufacturer to ensure the safety of persons and property during commissioning, start-up, operation, shut-down, maintenance periods and dismantling, as well as in the event of foreseeable faults or malfunctions that can occur in the equipment. These general safety requirements apply to all TPE, unless an exception is given in other parts of ISO 13577 dealing with specific equipment. The provisions of other parts of ISO 13577 that directly apply to specific types of TPE take precedence over the provisions of this document. ISO 13577-1:2016 is not applicable to blast furnaces, converters (in steel plants), boilers or equipment not covered under ISO 12100.
Fours industriels et équipements associés — Sécurité — Partie 1: Exigences générales
General Information
Relations
Standards Content (Sample)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13577-1
ISO/TC 244 Secretariat: JISC
Voting begins on: Voting terminates on:
2015-04-23 2015-07-23
Industrial furnaces and associated processing
equipment — Safety —
Part 1:
General requirements
Fours industriels et équipements associés — Sécurité —
Partie 1: Exigences générales
ICS: 13.100; 25.180.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 13577-1:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015
ISO/DIS 13577-1:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
ISO/DIS 13577-1:2015(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Safety requirements and/or protective measures . 2
4.1 General . 2
4.1.1 Requirements . 2
4.1.2 General design and construction requirements . 2
4.2 Mechanical safety. 4
4.2.1 General. 4
4.2.2 Crushing . 5
4.2.3 Shearing . 5
4.2.4 Entanglement. 5
4.2.5 Drawing-in. 5
4.2.6 Impact . 5
4.2.7 High-pressure fluid ejection . 6
4.2.8 Ejection of parts . 6
4.2.9 Slip/trip . 6
4.2.10 Falls . 6
4.2.11 Transport . 6
4.3 Electrical safety . 6
4.3.1 Electrical equipment of TPE . 6
4.3.2 Electroheat installations/equipment . 7
4.4 Thermal and cryogenic safety . 7
4.4.1 General. 7
4.4.2 Contact with hot/cold surfaces . 7
4.4.3 Fire/explosion . 8
4.4.4 Ejection of hot particles, work pieces and process liquids . 9
4.4.5 Thermal stress and other physiological effects . 9
4.5 Noise . 9
4.5.1 General. 9
4.5.2 Interference with communications .10
4.6 Vibration .10
4.7 Radiation safety .10
4.7.1 General.10
4.7.2 Non-ionizing radiation . .10
4.7.3 Ionizing radiation .11
4.8 Materials and substances processed, used or exhausted .11
4.8.1 General.11
4.8.2 Harmful by-products .11
4.8.3 Fire/explosion .11
4.9 Ergonomics .12
4.10 Hazard combination .12
4.10.1 General.12
4.11 Malfunction .12
4.11.1 Failure of power supply and auxiliary fluids .12
4.11.2 Errors of fitting/assembly during installation .12
4.11.3 Effect of malfunction of control system/component safety devices .12
4.12 Missing and incorrectly fitted safety devices .13
4.12.1 General.13
4.12.2 Power supply disconnection devices .13
ISO/DIS 13577-1:2015(E)
5 Verification .13
6 Information for use .16
6.1 General requirements .16
6.2 Location and nature of the information for use .17
6.3 Signals and warning devices .17
6.3.1 General.17
6.3.2 Marking .18
6.3.3 Personnel protection .18
6.3.4 Warning signs .18
6.4 Instruction handbook(s)/installation, commissioning, operation, maintenance, and de-
commissioning manual(s) .18
Annex A (informative) List of significant hazards.20
Annex B (informative) List of common industrial furnaces and
associatedprocessing equipment .29
Annex C (informative) Typical test report .33
Annex D (informative) Work-permit authorization .35
Annex E (normative) Requirements specific to Japan .36
Annex F (normative) Requirements specific to the USA .38
Annex G (normative) Requirements specific to the EU and associated countries .40
Annex H (normative) Requirements specific to Canada .
...
INTERNATIONAL ISO
STANDARD 13577-1
Second edition
2016-09-01
Industrial furnaces and associated
processing equipment — Safety —
Part 1:
General requirements
Fours industriels et équipements associés — Sécurité —
Partie 1: Exigences générales
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Safety requirements and/or protective measures . 2
4.1 General . 2
4.1.1 Requirements . 2
4.1.2 General design and construction requirements . 2
4.2 Mechanical safety. 4
4.2.1 General. 4
4.2.2 Crushing . 5
4.2.3 Shearing . 5
4.2.4 Entanglement. 5
4.2.5 Drawing-in. 5
4.2.6 Impact . 5
4.2.7 High-pressure fluid ejection . 6
4.2.8 Ejection of parts . 6
4.2.9 Slip/trip . 6
4.2.10 Falls . 6
4.2.11 Transport . 6
4.3 Electrical safety . 7
4.3.1 Electrical equipment of TPE . 7
4.3.2 Electroheat installations/equipment . 7
4.4 Thermal and cryogenic safety . 8
4.4.1 General. 8
4.4.2 Contact with hot/cold surfaces . 8
4.4.3 Fire/explosion . 8
4.4.4 Ejection of hot particles, work pieces and process liquids . 9
4.4.5 Thermal stress and other physiological effects . 9
4.5 Noise .10
4.5.1 General.10
4.5.2 Interference with communications .10
4.6 Vibration .10
4.7 Radiation safety .11
4.7.1 General.11
4.7.2 Non-ionizing radiation . .11
4.7.3 Ionizing radiation .11
4.8 Materials and substances processed, used or exhausted .12
4.8.1 General.12
4.8.2 Harmful by-products .12
4.8.3 Fire/explosion .12
4.9 Ergonomics .12
4.10 Hazard combination .13
4.11 Malfunction .13
4.11.1 Failure of power supply and auxiliary fluids .13
4.11.2 Errors of fitting/assembly during installation .13
4.11.3 Effect of malfunctions of the control system/component safety devices .13
4.12 Missing and incorrectly fitted safety devices .13
4.12.1 General.13
4.12.2 Power supply disconnection devices .13
5 Verification .14
6 Information for use .16
6.1 General requirements .16
6.2 Location and nature of the information for use .17
6.3 Signals and warning devices .17
6.3.1 General.17
6.3.2 Marking .17
6.3.3 Personnel protection .18
6.3.4 Warning signs .18
6.4 Instruction handbooks/manuals .18
Annex A (informative) List of significant hazards.20
Annex B (informative) List of common industrial furnaces and associatedprocessing equipment 29
Annex C (informative) Typical test report .33
Annex D (informative) Work-permit authorization .35
Annex E (informative) Information specific to Japan .37
Annex F (informative) Requirements specific to the USA .38
Annex G (informative) Requirements specific to the EU and associated countries .40
Annex H (informative) Requirements specific to Canada .42
Annex I (informative) Requirements specific to China .43
Bibliography .44
iv © ISO 2016 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.