ISO 18650-1:2021
(Main)Building construction machinery and equipment — Concrete mixers — Part 1: Commercial specifications
Building construction machinery and equipment — Concrete mixers — Part 1: Commercial specifications
This document establishes the content for commercial literature for concrete mixers used either as individual machines on building sites or as components of batching plants. Definitions refer to whole machines, their structure and parameters. The commercial specifications establish technical characteristics of the whole machines and their components. Truck mixers, as defined in ISO 19711‑1, are excluded from this document.
Machines et matériels pour la construction des bâtiments — Malaxeurs à béton — Partie 1: Spécifications commerciales
Le présent document établit le contenu de la littérature commerciale concernant les malaxeurs de béton utilisés comme machines individuelles sur les chantiers de construction ou constitutifs de centrales de production de béton. Les définitions se réfèrent à des machines complètes, à leur structure et à leurs paramètres. Les spécifications commerciales établissent les caractéristiques techniques des machines complètes et de leurs composants. Les bétonnières portées telles que définies dans l’ISO 19711‑1 sont exclues du présent document.
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 18650-1
Second edition
2021-05
Building construction machinery and
equipment — Concrete mixers —
Part 1:
Commercial specifications
Machines et matériels pour la construction des bâtiments —
Malaxeurs à béton —
Partie 1: Spécifications commerciales
Reference number
©
ISO 2021
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Description of the basic structures of concrete mixers . 6
4.1 Basic structure of gravity concrete mixers . 6
4.1.1 General. 6
4.1.2 Basic structure of self-loading mobile concrete mixer . 6
4.2 Basic structure of compulsory concrete mixers . 6
5 Commercial specifications . 6
5.1 Basic characteristics of a concrete mixer . 6
5.1.1 General data . 6
5.1.2 Detailed data for the concrete mixer components . 7
5.2 Dimensional characteristics of concrete mixers . 8
5.3 Other specifications for particular types of concrete mixers. 9
5.3.1 General. 9
5.3.2 Tipping drum gravity concrete mixer . 9
5.3.3 Reversing-drum concrete mixer . 9
5.3.4 Discharging-chute concrete mixer .10
5.3.5 Pan-type concrete mixers .10
5.3.6 Paddle concrete mixer . .12
5.3.7 Continuous-type concrete mixer . .12
5.3.8 Self-loading mobile concrete mixer .12
Annex A (informative) Examples of concrete mixer structures and dimensional characteristics .14
Bibliography .35
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 195, Building construction machinery and
equipment, Subcommittee SC 1, Machinery and equipment for concrete work.
This second edition cancels and replaces the first edition (ISO 18650-1:2004), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— added definition for "self-loading mobile concrete mixer" in 3.1.3.4 and also added reference to
Figures A.23 and A.24;
— added commercial specifications for discharging-chute concrete mixer in 5.3.4 and self-loading
mobile concrete mixer in 5.3.8;
— added Figures A.17 to A.22 for clarification of classification.
A list of all parts in the ISO 18650 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
INTERNATIONAL STANDARD ISO 18650-1:2021(E)
Building construction machinery and equipment —
Concrete mixers —
Part 1:
Commercial specifications
1 Scope
This document establishes the content for commercial literature for concrete mixers used either as
individual machines on building sites or as components of batching plants.
Definitions refer to whole machines, their structure and parameters.
The commercial specifications establish technical characteristics of the whole machines and their
components.
Truck mixers, as defined in ISO 19711-1, are excluded from this document.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
concrete mixer
machine designed for the production of concrete by mixing of measured (by mass or volume)
proportions of water, cement, aggregate and possibly chemical additives, within a certain time limit
Note 1 to entry: A concrete mixer can be furnished with the following accessories: charging skip hoist, fixed or
wheeled, or self-propelled supporting frame, mechanical shovel, water dosing equipment, and a skip weighing
system.
3.1.1
batch-type concrete mixer
concrete mixer (3.1) in which charging with concrete constituents and discharging of the drum are
carried out periodically, in batches
3.1.2
continuous-type concrete mixer
concrete mixer (3.1) in which charging with concrete constituents and discharging of the drum are
carried out continuously as an uninterrupted flow
Note 1 to entry: See Figures A.15 and A.16 for examples.
3.1.3
gravity concrete mixer
free-fall concrete mixer
concrete mixer (3.1) where mixing is performed by repeatedly elevating the mixed concrete and
dropping it from a certain height, inside a mixing drum, during its rotation
3.1.3.1
reversing-drum concrete mixer
reversing concrete mixer
gravity concrete mixer (3.1.3) with a reversible direction of rotation of the mixing drum where discharge
of mixed concrete is by reversing the rotation of the drum
Note 1 to entry: See Figures A.4 and A.5 for examples.
3.1.3.2
tipping-drum concrete mixer
free-fall concrete mixer (3.1.3) with a tipping mixing drum, open at one end for charging and discharging
of the concrete mix where discharging is carried out by tilting the drum
Note 1 to entry: See Figures A.1, A.2 and A.3 for examples.
3.1.3.3
discharging-chute concrete mixer
free-fall concrete mixer (3.1.3) with a mixing drum open at both sides where charging is carried out
from one side and discharging from the other by means of a chute entering the drum
Note 1 to entry: See Figure A.17 for an example.
3.1.3.4
self-loading mobile concrete mixer
gravity concrete mixer (3.1.3) with a reversible direction of rotation of the mixing drum where
discharge of mixed concrete is by reversing the rotation of the drum, integrated into a self-propelled
frame equipped with a self-loading attachment intended to use for a complete production and batching
of concrete, including transportation on road and off-road to reach the pouring site
Note 1 to entry: See Figures A.23 and A.24 for examples.
3.1.4
compulsory concrete mixer
concrete mixer (3.1) with mixing effected by the action of one or more agitators moving inside a mixing
chamber with either a vertical axis (pan) or horizontal axis (trough)
Note 1 to entry: See Figure A.18 for an example.
3.1.4.1
pan-type concrete mixer
compulsory concrete mixer (3.1.4) with agitators rotating about the vertical axis of a stationary or
rotating pan
3.1.4.2
turbo concrete mixer
compulsory concrete mixer (3.1.4) with an agitator rotating about the vertical axis of a stationary pan,
charged from the top and discharged by opening a segment of the pan bottom
Note 1 to entry: See Figures A.6, A.7 and A.8 for examples.
2 © ISO 2021 – All rights reserved
3.1.4.3
planetary concrete mixer
compulsory concrete mixer (3.1.4) with vertically mounted agitators having a planetary type of motion,
inside a stationary pan where the mixer is charged from the top, and discharged by opening a segment
of the pan bottom
Note 1 to entry: See Figures A.9 and A.10 for examples.
3.1.4.4
turbo planetary concrete mixer
compulsory concrete mixer (3.1.4) having one agitator rotating about the vertical axis of a stationary
pan in addition to other agitators in planetary motion where the mixer is charged from the top and
discharged by opening a segment of the pan bottom
Note 1 to entry: See Figure A.19 for an example.
3.1.4.5
counter-current operation concrete mixer
compulsory concrete mixer (3.1.4)with one or more agitators rotating about the vertical axes in a
counter-rotating pan where the mixer is charged from the top and discharged by opening a segment of
the pan bottom
Note 1 to entry: See Figure A.20 for an example.
3.1.4.6
concurrent operation concrete mixer
compulsory concrete mixer (3.1.4) with one or more agitators rotating about vertical axes in a pan
rotating concurrently where the mixer is charged from the top and discharged by opening a segment of
the pan bottom
Note 1 to entry: See Figure A.21 for example.
3.1.4.7
concrete mixer with high-speed stirrer
concrete mixer with high-speed activator
compulsory concrete mixer (3.1.4) with one or more agitators rotating about vertical axes including one
high speed agitator (activator) where the mixer is charged from the top and discharged by opening a
segment of the pan bottom
Note 1 to entry: See Figure A.22 for an example.
3.1.4.8
paddle concrete mixer
compulsory concrete mixer (3.1.4) with one or two paddle agitators rotating about horizontal axis in a
casing (trough) where the mixer is charged from the top and discharged by opening a segment of the
pan bottom
Note 1 to entry: The paddles may be straight or helix edged.
Note 2 to entry: See Figures A.11, A.12, A.13 and A.14 for examples.
3.2
charging time
t
duration, expressed in seconds, of charging the concrete components to the batch
...
NORME ISO
INTERNATIONALE 18650-1
Deuxième édition
2021-05
Machines et matériels pour la
construction des bâtiments —
Malaxeurs à béton —
Partie 1:
Spécifications commerciales
Building construction machinery and equipment — Concrete
mixers —
Part 1: Commercial specifications
Numéro de référence
©
ISO 2021
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Description des structures de base des malaxeurs à béton . 6
4.1 Structure de base des malaxeurs à béton par gravité . 6
4.1.1 Généralités . 6
4.1.2 Structure de base d’un malaxeur à béton mobile autochargeur. 6
4.2 Structure de base des malaxeurs à béton à mélange forcé . 6
5 Spécifications commerciales . 7
5.1 Caractéristiques de base d’un malaxeur à béton . 7
5.1.1 Données générales . 7
5.1.2 Données détaillées relatives aux composants des malaxeurs à béton . 8
5.2 Caractéristiques dimensionnelles des malaxeurs à béton . 9
5.3 Autres spécifications pour types particuliers de malaxeurs à béton . 9
5.3.1 Généralités . 9
5.3.2 Malaxeur à béton par gravité à tambour basculant . 9
5.3.3 Malaxeur à béton à tambour inverseur .10
5.3.4 Malaxeur à béton à goulotte de déchargement .10
5.3.5 Malaxeurs à béton à cuve .11
5.3.6 Malaxeur à béton à palettes .12
5.3.7 Malaxeur à béton de type production en continu .13
5.3.8 Malaxeur à béton mobile autochargeur .13
Annexe A (informative) Exemples de structures et de caractéristiques dimensionnelles
des malaxeurs à béton .14
Bibliographie .35
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 195, Machines et matériels pour la
construction des bâtiments, sous-comité SC 1, Machines et équipements pour la mise en œuvre du béton.
Cette deuxième édition annule et remplace la première édition (ISO 18650-1:2004), qui a fait l’objet
d’une révision technique.
Les principales modifications par rapport à l’édition précédente sont les suivantes:
— ajout de la définition «malaxeur à béton mobile autochargeur» en 3.1.3.4 et également ajout d’une
référence aux Figures A.23 et A.24.
— ajout des spécifications commerciales concernant le malaxeur à béton à goulotte de déchargement
en 5.3.4 et le malaxeur à béton mobile autochargeur en 5.3.8.
— ajout des Figures A.17 à A.22 pour clarifier la classification.
Une liste de toutes les parties de la série ISO 18650 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés
NORME INTERNATIONALE ISO 18650-1:2021(F)
Machines et matériels pour la construction des
bâtiments — Malaxeurs à béton —
Partie 1:
Spécifications commerciales
1 Domaine d’application
Le présent document établit le contenu de la littérature commerciale concernant les malaxeurs de béton
utilisés comme machines individuelles sur les chantiers de construction ou constitutifs de centrales de
production de béton.
Les définitions se réfèrent à des machines complètes, à leur structure et à leurs paramètres.
Les spécifications commerciales établissent les caractéristiques techniques des machines complètes et
de leurs composants.
Les bétonnières portées telles que définies dans l’ISO 19711-1 sont exclues du présent document.
2 Références normatives
Le présent document ne contient aucune référence normative.
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
3.1
malaxeur à béton
machine conçue pour la production de béton en mélangeant des proportions dosées (en masse ou en
volume) d’eau, de ciment, de granulat et éventuellement d’additifs chimiques, dans une certaine limite
de temps
Note 1 à l'article: Un malaxeur à béton peut être équipé des accessoires suivants: skip de chargement, châssis
porteur fixe, à roues ou automoteur, pelle mécanique, équipement de dosage de l’eau et système de pesage du
skip.
3.1.1
malaxeur à béton de type production discontinue
malaxeur à béton (3.1) dans laquelle le chargement des constituants du béton et le déchargement du
tambour sont réalisés périodiquement, par charges successives
3.1.2
malaxeur à béton de type production en continu
malaxeur à béton (3.1)dans laquelle le chargement des constituants du béton et le déchargement du
tambour sont réalisés en continu, sans interruption du débit
Note 1 à l'article: Voir les Figures A.15 et A.16 pour des exemples.
3.1.3
malaxeur à béton par gravité
malaxeur à béton à chute libre
malaxeur à béton (3.1) dans laquelle le malaxage est effectué en faisant, de manière répétée, monter
le béton et en le faisant tomber d’une certaine hauteur à l’intérieur du tambour mélangeur, pendant sa
rotation
3.1.3.1
malaxeur à béton à tambour inverseur
malaxeur à béton inverseur
malaxeur à béton par gravité (3.1.3), dont le sens de rotation du tambour mélangeur est inverseur, le
déchargement du béton mélangé étant effectué en inversant le sens de rotation du tambour
Note 1 à l'article: Voir les Figures A.4 et A.5 pour des exemples.
3.1.3.2
malaxeur à béton à tambour basculant
malaxeur à béton à chute libre (3.1.3) avec un tambour mélangeur basculant ouvert à une extrémité
pour le chargement et le déchargement du mélange de béton, le déchargement étant effectué en faisant
basculer le tambour
Note 1 à l'article: Voir les Figures A.1, A.2 et A.3 pour des exemples.
3.1.3.3
malaxeur à béton à goulotte de déchargement
malaxeur à béton à chute libre (3.1.3) avec un tambour mélangeur ouvert des deux côtés, le chargement
étant effectué d’un côté et le déchargement de l’autre, au moyen d’une goulotte qui entre dans le tambour
Note 1 à l'article: Voir la Figure A.17 pour un exemple.
3.1.3.4
malaxeur à béton mobile autochargeur
malaxeur à béton par gravité (3.1.3), dont le sens de rotation du tambour mélangeur est inverseur, le
déchargement du béton mélangé étant effectué en inversant le sens de rotation du tambour, intégrée
dans un châssis automoteur équipé d’un accessoire autochargeur destiné à être utilisé pour une
production et un dosage complets du béton, y compris le transport sur route et sur chantier jusqu’au
site de distribution
Note 1 à l'article: Voir les Figures A.23 et A.24 pour des exemples.
3.1.4
malaxeur à béton à mélange forcé
malaxeur à béton (3.1) dans laquelle le malaxage est effectué sous l’action d’un ou plusieurs agitateurs
qui se déplacent à l’intérieur d’une chambre de malaxage selon un axe vertical (cuve) ou un axe
horizontal (goulotte)
Note 1 à l'article: Voir la Figure A.18 pour un exemple.
3.1.4.1
malaxeur à béton à cuve
malaxeur à béton à mélange forcé (3.1.4) avec des agitateurs qui tournent autour de l’axe vertical d’une
cuve fixe ou rotative
2 © ISO 2021 – Tous droits réservés
3.1.4.2
malaxeur à béton de type turbo
malaxeur à béton à mélange forcé (3.1.4) avec un agitateur qui tourne autour de l’axe vertical d’une cuve
fixe chargée depuis le dessus et vidangée par l’ouverture d’un segment au fond de la cuve
Note 1 à l'article: Voir les Figures A.6, A.7 et A.8 pour des exemples.
3.1.4.3
malaxeur à béton de type planétaire
malaxeur à béton à mélange forcé (3.1.4) avec des agitateurs montés verticalement effectuant un
mouvement de type planétaire à l’intérieur d’une cuve fixe, le malaxeur étant chargé depuis le dessus et
vidangé par l’ouverture d’un segment au fond de la cuve
Note 1 à l'article: Voir les Figures A.9 et A.10 pour des exemples.
3.1.4.4
malaxeur à béton de type turbo-planétaire
malaxeur à béton à mélange forcé (3.1.4) avec un agitateur qui tourne autour de l’axe vertical d’une cuve
fixe, en plus d’autres agitateurs effectuant un mouvement planétaire, le malaxeur étant chargé depuis le
dessus et vidangé par l’ouverture d’un segment au fond de la cuve
Note 1 à l'article: Voir la Figure A.19 pour un exemple.
3.1.4.5
malaxeur à béton de type contre-courant
malaxeur à béton à mélange forcé (3.1.4) avec un ou plusieurs agitateurs qui tourn
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.