ISO 15708-4:2025
(Main)Non-destructive testing — Radiation methods for computed tomography — Part 4: Qualification
Non-destructive testing — Radiation methods for computed tomography — Part 4: Qualification
This document gives guidance on the qualification of the performance of a computed tomography (CT) system with respect to various testing tasks. This document is applicable only to industrial imaging (i.e. non-medical applications) and provides a consistent set of definitions of CT performance parameters, including the relationship between these performance parameters and CT system specifications. This document is applicable to industrial computed tomography. This document does not apply to other techniques of tomography such as translational tomography and tomosynthesis.
Essais non destructifs — Méthodes par rayonnements pour la tomographie informatisée — Partie 4: Qualification
Le présent document donne des recommandations sur la qualification de la performance d’un système de tomographie informatisée (TI) par rapport à différentes tâches d’essai. Il est uniquement applicable à l’imagerie industrielle (c'est-à-dire aux applications non médicales) et fournit un ensemble cohérent de définitions des paramètres de performance de la TI, y compris la relation entre ces paramètres de performance et les spécifications du système TI. Le présent document est applicable à la tomographie informatisée industrielle. Il ne s’applique pas aux autres techniques de tomographie telles que la tomographie par translation et la tomosynthèse.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 15708-4
Second edition
Non-destructive testing —
2025-06
Radiation methods for computed
tomography —
Part 4:
Qualification
Essais non destructifs — Méthodes par rayonnements pour la
tomographie informatisée —
Partie 4: Qualification
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Qualification of the testing . 1
4.1 General .1
4.2 Qualification of defect testing .2
4.2.1 General .2
4.2.2 Objects and features .2
4.2.3 Feature detectability/test system/system parameterisation .2
4.2.4 Verification of suitability .3
4.2.5 Consistency check .3
4.2.6 Documentation.4
4.3 Qualification of dimensional testing .4
4.3.1 General .4
4.3.2 Test and measurement task .4
4.3.3 Dimensional testing/test system/system parameterisation .4
4.3.4 Degree of accuracy .5
4.3.5 Consistency check .5
4.3.6 Documentation.5
5 Qualification of the CT system . 6
5.1 General .6
5.2 Integral overall system verification .6
5.3 Checking the system components .6
5.3.1 General .6
5.3.2 Manipulation system .6
5.3.3 Image scale .6
5.3.4 Beam axis perpendicularity .6
5.3.5 Tube focal spot . . .6
5.3.6 Tube stability .7
5.3.7 Detector .7
5.3.8 Reconstruction . . .7
5.3.9 Visualization .7
5.4 Documentation .7
6 Example of CT system resolution evaluation methods . 7
6.1 General .7
6.2 Acquisition parameters .8
6.3 Recommendations for creating reference objects .8
6.4 Density resolution measurement method .8
6.4.1 General .8
6.4.2 High energy reference object .9
6.4.3 Low energy reference object .9
6.4.4 Experimental measurements .9
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 135, Non-destructive testing, Subcommittee SC
5, Radiographic testing, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 138, Non-destructive testing, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 15708-4:2017), which has been technically
revised.
The main changes are as follows:
— addition of ISO 15708-1 and ISO 15708-3 as normative references in Clause 2;
— correction of title in Figure 1;
— correction of density values d of each insert and CT grey values N in 6.4.4;
R i
— deletion of the bibliography;
— editorial changes.
A list of all parts in the ISO 15708 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 15708-4:2025(en)
Non-destructive testing — Radiation methods for computed
tomography —
Part 4:
Qualification
1 Scope
This document gives guidance on the qualification of the performance of a computed tomography (CT)
system with respect to various testing tasks.
This document is applicable only to industrial imaging (i.e. non-medical applications) and provides a
consistent set of definitions of CT performance parameters, including the relationship between these
performance parameters and CT system specifications.
This document is applicable to industrial computed tomography.
This document does not apply to other techniques of tomography such as translational tomography and
tomosynthesis.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 15708-1, Non-destructive testing — Radiation methods for computed tomography — Part 1: Vocabulary
ISO 15708-3:2025, Non-destructive testing — Radiation methods for computed tomography — Part 3: Operation
and interpretation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 15708-1 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Qualification of the testing
4.1 General
CT is used in industry both for defect testing and analysis as well as dimensional testing and measurement.
Since CT does not provide a direct measurement of the desired quantities such as e.g. pore size or wall
thickness, these quantities shall be derived from
...
Norme
internationale
ISO 15708-4
Deuxième édition
Essais non destructifs — Méthodes
2025-06
par rayonnements pour la
tomographie informatisée —
Partie 4:
Qualification
Non-destructive testing — Radiation methods for computed
tomography —
Part 4: Qualification
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Qualification des essais . 1
4.1 Généralités .1
4.2 Qualification de l’inspection de défaut .2
4.2.1 Généralités .2
4.2.2 Objets et caractéristiques .2
4.2.3 Détectabilité des caractéristiques/système d’essai/paramétrage du système .3
4.2.4 Vérification de pertinence.3
4.2.5 Contrôle de cohérence .4
4.2.6 Documentation.4
4.3 Qualification de l’essai dimensionnel .4
4.3.1 Généralités .4
4.3.2 Essai et tâche de mesure .4
4.3.3 Essai dimensionnel/système d’essai/paramétrage du système .4
4.3.4 Degré d'exactitude .5
4.3.5 Contrôle de cohérence .6
4.3.6 Documentation.6
5 Qualification du système TI . 6
5.1 Généralités .6
5.2 Vérification intégrale de l’ensemble du système .6
5.3 Vérification des composants du système .7
5.3.1 Généralités .7
5.3.2 Système de manipulation .7
5.3.3 Échelle de l’image .7
5.3.4 Perpendicularité de l’axe du faisceau .7
5.3.5 Foyer d’émission du tube.7
5.3.6 Stabilité du tube .7
5.3.7 Détecteur .7
5.3.8 Reconstruction . . .7
5.3.9 Visualisation .7
5.4 Documentation .8
6 Exemple de méthodes d’évaluation de la résolution du système TI . 8
6.1 Généralités .8
6.2 Paramètres d’acquisition . .8
6.3 Recommandations pour la création d’objets de référence .8
6.4 Méthode de mesure de résolution en densité .9
6.4.1 Généralités .9
6.4.2 Objet de référence à haute énergie .9
6.4.3 Objet de référence à faible énergie .10
6.4.4 Mesures expérimentales .10
iii
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l’ISO n'avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l'adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de propriété.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de
l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.html.
Le présent document a été élaboré par le comité technique ISO/TC 135, Essais non destructifs, sous-
comité SC 5, Contrôle par radiographie, en collaboration avec le comité technique du Comité européen de
normalisation (CEN), CEN/TC 138, Essais non destructifs, conformément à l’Accord de coopération technique
entre l’ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 15708-4:2017), qui a fait l'objet d'une
révision technique.
Les principales modifications sont les suivantes:
— ajout de l’ISO 15708-1 et de l’ISO 15708-3 comme références normatives dans l'Article 2;
— correction du titre de la Figure 1;
— correction des valeurs de densité d de chaque insert et des valeurs de gris TI N en 6.4.4;
R i
— suppression de la bibliographie;
— modifications rédactionnelles.
Une liste de toutes les parties de la série ISO 15708 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/members.html.
iv
Norme internationale ISO 15708-4:2025(fr)
Essais non destructifs — Méthodes par rayonnements pour la
tomographie informatisée —
Partie 4:
Qualification
1 Domaine d'application
Le présent document donne des recommandations sur la qualification de la performance d’un système de
tomographie informatisée (TI) par rapport à différentes tâches d’essai.
Il est uniquement applicable à l’imagerie industrielle (c'est-à-dire aux applications non médicales) et fournit
un ensemble cohérent de définitions des paramètres de performance de la TI, y compris la relation entre ces
paramètres de performance et les spécifications du système TI.
Le présent document est applicable à la tomographie informatisée industrielle.
Il ne s’applique pas aux autres techniques de tomographie telles que la tomographie par translation et la
tomosynthèse.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour
les références non datées, la dernière édition du document de référence s’applique (y compris les éventuels
amendements).
ISO 15708-1, Essais non destructifs — Méthodes par rayonnements pour la tomographie informatisée — Partie
1: Vocabulaire
ISO 15708-3:2025, Essais non destructifs — Méthodes par rayonnements pour la tomographie informatisée —
Partie 3: Fonctionnement et interprétation
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 15708-1 s’appliquent.
L’ISO et l’IEC tiennent à j
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.