ISO 37:2017
(Main)Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 37:2017 specifies a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers. The properties which can be determined are tensile strength, elongation at break, stress at a given elongation, elongation at a given stress, stress at yield and elongation at yield. The measurement of stress and strain at yield applies only to some thermoplastic rubbers and certain other compounds.
Caoutchouc vulcanisé ou thermoplastique — Détermination des caractéristiques de contrainte-déformation en traction
L'ISO 37.2017 décrit une méthode pour la détermination des caractéristiques de contrainte-déformation en traction des caoutchoucs vulcanisés ou thermoplastiques. Les caractéristiques susceptibles d'être déterminées sont la résistance à la traction, l'allongement à la rupture, la contrainte pour une déformation donnée, l'allongement sous une contrainte donnée, la contrainte au seuil visco-élastique et l'allongement au seuil visco-élastique. Le mesurage de la contrainte de traction et de l'allongement au seuil visco-élastique ne s'applique qu'à certains caoutchoucs thermoplastiques et à certains autres mélanges
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 37
Sixth edition
2017-11
Rubber, vulcanized or
thermoplastic — Determination of
tensile stress-strain properties
Caoutchouc vulcanisé ou thermoplastique — Détermination des
caractéristiques de contrainte-déformation en traction
Reference number
©
ISO 2017
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 4
5 General . 4
6 Test pieces . 4
6.1 General . 4
6.2 Dumb-bells . 5
6.3 Rings. 5
7 Apparatus . 6
7.1 Dies and cutters . 6
7.2 Thickness gauge . 6
7.3 Cone gauge . 6
7.4 Tensile-testing machine . 7
7.5 Test rig for ring test pieces . 8
8 Number of test pieces . 9
9 Preparation of test pieces . 9
9.1 Dumb-bells . 9
9.2 Rings. 9
10 Conditioning of sample and test pieces . 9
10.1 Time between vulcanization and testing . 9
10.2 Protection of samples and test pieces .10
10.3 Conditioning of samples .10
10.4 Conditioning of test pieces .10
11 Marking of dumb-bell test pieces .10
12 Measurement of test pieces .10
12.1 Dumb-bells .10
12.2 Rings.11
12.3 Comparison of groups of test pieces .11
13 Procedure.11
13.1 Dumb-bell test pieces .11
13.2 Ring test pieces .11
14 Temperature of test .12
15 Calculation of results .12
15.1 Dumb-bells .12
15.2 Ring test pieces .13
16 Expression of results .14
17 Precision .14
18 Test report .15
Annex A (informative) Preparation of type B ring test pieces .16
Annex B (informative) Precision .19
Annex C (informative) Analysis of ITP data and dumb-bell shape .26
Bibliography .30
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 2, Testing and analysis.
This sixth edition cancels and replaces the fifth edition (ISO 37:2011), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the cutter angle range in Figure 3 has been changed to 30° - 35°;
— dimension B of the dumb-bell test piece has been corrected in Figure 3;
— accuracy requirement for force measurement has been changed to Class 1;
— dimensions of ∅d and ∅d in Figure 5 and Table 3 have been corrected;
1 2
— the test results of interlaboratory test programmes (ITP) have been added.
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 37:2017(E)
Rubber, vulcanized or thermoplastic — Determination of
tensile stress-strain properties
WARNING 1 — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices and to
determine the applicability of any other restrictions.
WARNING 2 — Certain procedures specified in this document might involve the use or generation
of substances, or the generation of waste, that could constitute a local environmental hazard.
Reference should be made to appropriate documentation on safe handling and disposal after use.
1 Scope
This document specifies a method for the determination of the tensile stress-strain properties of
vulcanized and thermoplastic rubbers.
The properties which can be determined are tensile strength, elongation at break, stress at a given
elongation, elongation at a given stress, stress at yield and elongation at yield. The measurement of
stress and strain at yield applies only to some thermoplastic rubbers and certain other compounds.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 5893, Rubber and plastics test equipment — Tensile, flexural and compression types (constant rate of
traverse) — Specification
ISO 23529:2016, Rubber — General procedures for preparing and conditioning test pieces for physical
test methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://
...
NORME ISO
INTERNATIONALE 37
Sixième édition
2017-11
Caoutchouc vulcanisé ou
thermoplastique — Détermination
des caractéristiques de contrainte-
déformation en traction
Rubber, vulcanized or thermoplastic — Determination of tensile
stress-strain properties
Numéro de référence
©
ISO 2017
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe . 4
5 Généralités . 4
6 Éprouvettes . 5
6.1 Généralités . 5
6.2 Haltères . 5
6.3 Anneaux . 6
7 Appareillage . 6
7.1 Emporte-pièce et lames . 6
7.2 Mesureur d'épaisseur . 7
7.3 Jauge conique . 7
7.4 Machine d'essai de traction . 8
7.5 Appareillage d'essai pour les éprouvettes annulaires . 9
8 Nombre d'éprouvettes .10
9 Préparation des éprouvettes .10
9.1 Haltères .10
9.2 Anneaux .10
10 Conditionnement des échantillons et des éprouvettes .11
10.1 Délai entre vulcanisation et essai .11
10.2 Protection des échantillons et des éprouvettes .11
10.3 Conditionnement des échantillons .11
10.4 Conditionnement des éprouvettes .11
11 Marquage des éprouvettes haltères .11
12 Mesurage des éprouvettes .12
12.1 Haltères .12
12.2 Anneaux .12
12.3 Comparaison de groupes d'éprouvettes .12
13 Mode opératoire.12
13.1 Éprouvettes haltères .12
13.2 Éprouvettes annulaires .12
14 Température d'essai .13
15 Calcul des résultats .13
15.1 Éprouvettes haltères .13
15.2 Éprouvettes annulaires .14
16 Expression des résultats.15
17 Fidélité .16
18 Rapport d'essai .16
Annexe A (informative) Préparation des éprouvettes annulaires de type B .17
Annexe B (informative) Fidélité.20
Annexe C (informative) Analyse des données d'ITP avec la forme haltère .27
Bibliographie .31
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 45, Élastomères et produits à base
d'élastomères, sous-comité SC 2, Essais et analyses.
Cette sixième édition annule et remplace la cinquième édition (ISO 37:2011), qui a fait l'objet d'une
révision technique.
Les principales modifications par rapport à la précédente édition sont les suivantes:
— l’angle de coupe à la Figure 3 a été modifié à 30° - 35°;
— la dimension B de l’éprouvette haltère a été corrigée à la Figure 3;
— la précision requise pour le mesurage de la force a été modifiée en Classe 1;
— les dimensions de ∅d et ∅d à la Figure 5 et dans le Tableau 3 ont été corrigées;
1 2
— les résultats de programmes d’essai interlaboratoires (ITP) ont été ajoutés.
iv © ISO 2017 – Tous droits réservés
NORME INTERNATIONALE ISO 37:2017(F)
Caoutchouc vulcanisé ou thermoplastique —
Détermination des caractéristiques de contrainte-
déformation en traction
AVERTISSEMENT 1 — Il convient que l'utilisateur du présent document connaisse bien les
pratiques courantes de laboratoire. Le présent document n'a pas pour but de traiter tous les
problèmes de sécurité qui sont, le cas échéant, liés à son utilisation. Il incombe à l'utilisateur
d'établir des pratiques appropriées en matière d'hygiène et de sécurité, et de déterminer et de
déterminer l'applicabilité de toute autre restriction.
AVERTISSEMENT 2 — Certains modes opératoires spécifiés dans le présent document peuvent
impliquer l'utilisation ou la génération de substances ou de déchets pouvant représenter
un danger environnemental local. Il convient de se référer à la documentation appropriée
concernant la manipulation et l'élimination après usage en toute sécurité.
1 Domaine d'application
Le présent document décrit une méthode pour la détermination des caractéristiques de contrainte-
déformation en traction des caoutchoucs vulcanisés ou thermoplastiques.
Les caractéristiques susceptibles d'être déterminées sont la résistance à la traction, l’allongement à
la rupture, la contrainte pour une déformation donnée, l’allongement sous une contrainte donnée, la
contrainte au seuil visco-élastique et l’allongement au seuil visco-élastique. Le mesurage de la contrainte
de traction et de l'allongement au seuil visco-élastique ne s'applique qu'à certains caoutchoucs
thermoplastiques et à certains autres mélanges.
2 Références normatives
Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des
exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les
références non datées, la dernière édition du
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.