Abstract

This document specified the test cycles for measurement for the gaseous exhaust emissions from motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable to motorcycles equipped with a spark ignition engine (four-stroke engine or rotary piston engine).

Status
Published
Publication Date
19-Nov-2026
Current Stage
6060 - International Standard published
Start Date
20-Nov-2026
Completion Date
20-Nov-2026

Buy Documents

Standard

ISO 6460-2:2026 - Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 2: Test cycles and specific test conditions

Release Date:20-Nov-2026
English language (61 pages)
sale 15% off
Preview
sale 15% off
Preview

ISO 6460-2:2026 is an ISO standard for motorcycles. It specifies the test cycles and specific test conditions used to measure gaseous exhaust emissions and to determine fuel consumption for motorcycles as defined in ISO 3833.

It applies to motorcycles equipped with a spark ignition engine, including four-stroke engines and rotary piston engines. The document is intended for emissions testing, fuel-consumption testing and the reporting of those results.

What does ISO 6460-2:2026 specify?

ISO 6460-2:2026 specifies the driving cycles, test-room conditions, motorcycle classes, gearshift rules, test procedures and result presentation used for motorcycle emissions and fuel-consumption measurements. It is structured around a main test-cycle clause and two normative result-presentation annexes, with two informative annexes for additional background.

The main body contains Scope, normative references, terms and definitions, test cycle, and presentation of results. Annex A and Annex B give the reporting formats for gaseous exhaust emissions and fuel consumption, while Annex C and Annex D provide informative reference cycles and an explanatory note on gearshift procedure.

AnnexWhat it covers
Annex APresentation of results for gaseous exhaust emissions
Annex BPresentation of results of fuel consumption
Annex CTest cycles
Annex DExplanatory note on the gearshift procedure

What are the key requirements of ISO 6460-2:2026?

ISO 6460-2:2026 is mainly about how to run the motorcycle on the chassis dynamometer and how to classify the vehicle so the correct cycle and weighting are used. In practice, the document defines the speed trace, the ambient conditions, the gear selection logic and the way results are combined.

Motorcycle classification and test-cycle selection

Clause 4.3 classifies motorcycles by engine capacity and maximum motorcycle speed, using the values exactly as measured - they are not to be rounded. That matters because the class determines which cycle parts are run and how the final result is weighted.

Clause 4.4.1 links each class to a specific sequence of cycle parts:

  • class 1 runs part 1 in cold condition, then part 1 in hot condition
  • class 2 subclass 2-1 runs part 1 cold, then part 2 hot
  • class 2 subclass 2-2 runs part 1 cold, then part 2 hot
  • class 3 subclass 3-1 runs part 1 cold, then part 2 hot, then part 3 reduced speed hot
  • class 3 subclass 3-2 runs part 1 cold, then part 2 hot, then part 3 hot

Clause 4.8 provides the detailed second-by-second speed traces for those parts. In practice, the test lab has to select the correct trace before the run begins.

Test-room conditions and speed control

Clause 4.2 sets the test-room temperature for the chassis dynamometer and gas sample collection device at 298 K ±5 K. The room temperature is measured twice near the motorcycle cooling blower, both before and after the type 1 test. This keeps the test environment controlled and documented.

Clause 4.4.1.2 sets the allowable speed tolerance around the prescribed trace. Small short-duration excursions can be accepted during gear changes, but if the run does not remain within the defined tolerance, the result is not used and the run is repeated. That matters because the emissions result depends on following the cycle closely enough to make the test valid.

Gear selection and shifting

Clause 4.4.2 gives separate gear rules for automatic and manual transmissions. Automatic motorcycles are tested in the manufacturer-recommended street or highway configuration, with automatic transmissions in “drive” and normal shifting sequence. Manual transmissions use calculated shift speeds based on rated power, kerb mass, idle speed, rated engine speed and gear ratios.

Clause 4.4.2.2.1 also sets practical gear-choice rules sample by sample, using the phase indicators built into the cycle tables. The document limits gear changes so the test reflects the intended shift strategy, including rules against downshifts during acceleration and against large multi-gear jumps. For the reader, this means the gearbox setting is not left to driver judgment alone - it is prescribed and traceable.

Type 1 and type 2 test procedure

Clause 4.6.1.1 sets the start-up and restart rules for the type 1 test, including how to handle cold starts, hot starts and stalls. Clause 4.6.1.2 requires minimum throttle movement to hold the trace and prohibits simultaneous brake and throttle use. Clause 4.6.1.3 describes the full dynamometer sequence, including sample bags, constant volume sampling, fan operation, sample switching between cycle parts and timing of engine shutdown.

Clause 4.5 defines the type 2 test, which applies only to motorcycles powered by a positive-ignition engine. It is carried out immediately after the type 1 test at normal idle and “high idle” speed, with the gear lever or selector in the specified neutral or park position. Clause 4.6.2.2 also describes the exhaust sampling arrangement, including the extension at the tailpipe and the handling of multiple outlets.

Result analysis and reporting

Clause 4.7.1 says bag analysis for the type 1 test should begin as soon as possible and not later than 30 min after the test. It also sets the averaging and weighting of the cycle-part results into a final result for each class. For fuel consumption and gaseous emissions, that weighting is what converts the separate cycle parts into the reported value.

Clause 4.7.2 gives the correction rule for type 2 carbon monoxide concentration and notes when correction is not needed for four-stroke engines. Annex A and Annex B then define the data fields to report, including vehicle identification, test fuel, dynamometer settings, room conditions, sampling system details and the final emission or fuel-consumption results.

Who uses ISO 6460-2:2026?

ISO 6460-2:2026 is used by motorcycle manufacturers, emissions laboratories, type-approval and certification teams, and quality managers who need a repeatable test cycle for engine and vehicle approval work. It is also used by test engineers who set up the chassis dynamometer, run the cycle and calculate the final emissions and fuel-consumption results.

It is relevant to organizations working on spark ignition motorcycles, including four-stroke and rotary piston engines, where the test must be documented in a way that can be compared across vehicles and laboratories.

What changed in ISO 6460-2:2026 from the previous edition?

ISO 6460-2:2026 cancels and replaces ISO 6460-2:2014, and the foreword says the document has been technically revised.

The changes stated in the document are:

  • the description of the test cycle formerly placed in the Scope is now in the General section of the test cycle
  • UN GTR No.2 (WMTC) has been added to the normative references
  • the test cycle is stated to be equivalent to the cycle specified in WMTC
  • the starting sequence at the beginning of the test cycle has been corrected
  • the cycle from European Union Commission Directive 2003/77/EC is described in Annex C for information
  • an explanation of the gear-shift calculation is included in Annex D for information

Which standards are used with ISO 6460-2:2026?

ISO 6460-2:2026 cites four normative references that support the test method:

  • ISO 4106 - provides the net power value used in the gearshift calculations and reporting
  • ISO 6460-1 - gives the general test requirements and the calculation method used with this part
  • ISO 7117 - provides the method for determining maximum speed, which is needed for motorcycle classification
  • UN GTR No.2 (WMTC) - provides the equivalent world-harmonized motorcycle test procedure

The bibliography also names ISO 3833, ISO 6460-3, ISO 6726 and ISO 11486 as related standards. ISO 3833 defines the motorcycle terminology used in the scope, ISO 6460-3 covers constant-speed fuel-consumption measurement, ISO 6726 covers masses vocabulary, and ISO 11486 covers setting running resistance on a chassis dynamometer.

What does the ISO 6460-2:2026 document contain?

ISO 6460-2:2026 contains the full motorcycle class classification, the test-room condition requirements, the gearshift calculation logic and the detailed operating traces for each type 1 cycle part. The cycle tables in clause 4.8 give the speed pattern second by second for each class and subclass.

It also contains the procedures for starting, restarting, stalling recovery, driving on the dynamometer, sample collection and analysis, and the correction and weighting rules used to derive the final results. Annex A and Annex B provide reporting templates for emissions and fuel consumption, including fields for the motorcycle, fuel, dynamometer, room conditions and measured outputs.

Annex C gives three informative reference test cycles, with figures showing their operating cycles on a chassis dynamometer. Annex D explains how the gearshift procedure was developed and how the normalised shift-speed equations are approached in practice.

Relations

Effective Date
29-Jun-2024

Buy Documents

Standard

ISO 6460-2:2026 - Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 2: Test cycles and specific test conditions

Release Date:20-Nov-2026
English language (61 pages)
sale 15% off
Preview
sale 15% off
Preview

Get Certified

Connect with accredited certification bodies for this standard

TÜV Rheinland

TÜV Rheinland is a leading international provider of technical services.

DAKKS Germany Verified

TÜV SÜD

TÜV SÜD is a trusted partner of choice for safety, security and sustainability solutions.

DAKKS Germany Verified

DEKRA Certification Inc.

DEKRA US certification services.

ANAB United States Verified

Sponsored listings

Frequently Asked Questions

ISO 6460-2:2026 is a standard published by the International Organization for Standardization (ISO). Its full title is "Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 2: Test cycles and specific test conditions". This standard covers: This document specified the test cycles for measurement for the gaseous exhaust emissions from motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable to motorcycles equipped with a spark ignition engine (four-stroke engine or rotary piston engine).

This document specified the test cycles for measurement for the gaseous exhaust emissions from motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable to motorcycles equipped with a spark ignition engine (four-stroke engine or rotary piston engine).

ISO 6460-2:2026 is classified under the following ICS (International Classification for Standards) categories: 13.040.50 - Transport exhaust emissions; 43.140 - Motorcycles and mopeds. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO 6460-2:2026 has the following relationships with other standards: It is inter standard links to ISO 6460-2:2014. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ISO 6460-2:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


International
Standard
ISO 6460-2
Third edition
Motorcycles — Measurement
2026-11
method for gaseous exhaust
emissions and fuel consumption —
Part 2:
Test cycles and specific test
conditions
Motocycles — Méthode de mesure des émissions de gaz
d'échappement et de la consommation de carburant —
Partie 2: Conditions d'essai spécifiques et cycles d'essai
Reference number
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test cycle . 1
4.1 General .1
4.2 Test room conditions.1
4.3 Motorcycle classification .2
4.3.1 General .2
4.3.2 Class 1 .2
4.3.3 Class 2 .2
4.3.4 Class 3 .2
4.4 Type 1 tests . .3
4.4.1 Driving schedules .3
4.4.2 Gearshift prescriptions .5
4.5 Type 2 tests . .8
4.5.1 Application .8
4.5.2 Measured gaseous pollutant .8
4.5.3 Engine test speeds .8
4.5.4 Gear lever position .8
4.6 Test procedures .8
4.6.1 Type 1 tests .8
4.7 Analysis of results .11
4.7.1 Type 1 tests .11
4.7.2 Type 2 tests . 12
4.8 Driving cycles for type 1 tests . 13
5 Presentation of results .50
Annex A (normative) Presentation of results for gaseous exhaust emissions .51
Annex B (normative) Presentation of results of fuel consumption .54
Annex C (informative) Test cycles .57
Annex D (informative) Explanatory note on the gearshift procedure .59
Bibliography . 61

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 38,
Motorcycles and mopeds.
This third edition cancels and replaces the second edition (ISO 6460-2:2014), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— The description of the test cycle described for the Scope is appropriately placed in the General section of
the test cycle.
— Added “UN GTR No.2 (WMTC) “ to the Normative references.
— The test cycle is equivalent to the test cycle specified in WMTC.
[6]
— The test cycle specified in European Union Commission Directive 2003/77/EC is described in Annex C
for information.
— An explanation of the gear shift calculation is included in Annex D for information.
A list of all parts in the ISO 6420 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
Introduction
This document has been prepared to provide details of the typical test cycles for measurement of gaseous
exhaust emissions and fuel consumption. The measurements can be carried out by referring to this
document and to ISO 6460-1.
The following revisions are mainly made in this document.
— The description of the test cycle described for the Scope is appropriately placed in the General section of
the test cycle.
— Added “UN GTR No.2 (WMTC) “ to the Normative references.
— The test cycle is equivalent to the test cycle specified in WMTC.
— Corrected the starting sequence at test cycle start.
[6]
— The test cycle specified in European Union Commission Directive 2003/77/EC is described in Annex C
for information.
— An explanation of the gear shift calculation is included in Annex D for information.

v
International Standard ISO 6460-2:2026(en)
Motorcycles — Measurement method for gaseous exhaust
emissions and fuel consumption —
Part 2:
Test cycles and specific test conditions
1 Scope
This document specified the test cycles for measurement for the gaseous exhaust emissions from
motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable
to motorcycles equipped with a spark ignition engine (four-stroke engine or rotary piston engine).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 4106, Motorcycles — Engine test code — Net power
ISO 6460-1, Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part
1: General test requirements
ISO 7117, Motorcycles — Measurement method for determining maximum speed
UN GTR No.2 (WMTC) — Measurement procedure for two-wheeled motorcycles equipped with a positive
or compression ignition engine with regard to the emission of gaseous pollutants, CO emissions and fuel
consumption.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Test cycle
4.1 General
The test cycle is equivalent to the test cycle specified in WMTC.
4.2 Test room conditions
The test room with the chassis dynamometer and the gas sample collection device shall have a temperature
of 298 K ±5 K. The room temperature shall be measured twice in the vicinity of motorcycle cooling blower
(fan), both before and after the type 1 test.

4.3 Motorcycle classification
4.3.1 General
Figure 1 gives an overview of the motorcycle classification in terms of engine capacity and maximum
motorcycle speed. The numerical values of the engine capacity and maximum motorcycle speed shall not be
rounded up or down.
4.3.2 Class 1
Motorcycles that fulfil either of the following specifications belong to class 1:
3 3 3
50 cm < engine capacity < 150 cm and v ≤ 50 km/h or engine capacity < 150 cm and
max
50 km/h < v < 100 km/h.
max
4.3.3 Class 2
Motorcycles that fulfil either of the following specifications belong to class 2:
3 3
a) subclass 2-1: engine capacity < 150 cm and 100 km/h ≤ v < 115 km/h or engine capacity ≥ 150 cm
max
and v < 115 km/h;
max
b) subclass 2-2: 115 km/h ≤ v < 130 km/h.
max
4.3.4 Class 3
Motorcycles that fulfil either of the following specifications belong to class 3:
a) subclass 3-1: 130 km/h ≤ v < 140 km/h;
max
b) subclass 3-2: v ≥ 140 km/h.
max
Key
X engine capacity, cm
Y maximum motorcycle speed, km/h
1 class 1
2 class 2 subclass 2-1
3 class 2 subclass 2-2
4 class 3 subclass 3-1
5 class 3 subclass 3-2
Figure 1 — Motorcycle classification
4.4 Type 1 tests
4.4.1 Driving schedules
4.4.1.1 Test cycles
Test cycles (motorcycle speed patterns) for the type 1 test consists of up to three parts that are shown in 4.8.
Depending on the motorcycle class (see 4.3), the following test cycle parts shall be run.
a) class 1:
part 1, reduced speed in cold condition, followed by part 1 reduced speed in hot condition;
b) class 2:
1) subclass 2-1: part 1, reduced speed in cold condition, followed by part 2, reduced speed in hot
condition;
2) subclass 2-2: part 1 in cold condition, followed by part 2 in hot condition;
c) class 3:
1) subclass 3-1: part 1 in cold condition, followed by part 2 in hot condition, followed by part 3 reduced
speed in hot condition;
2) subclass 3-2: part 1 in cold condition, followed by part 2 in hot condition, followed by part 3 in hot
condition.
4.4.1.2 Speed tolerances
The speed tolerance at any given time on the test cycle prescribed in 4.4.1.1 is defined by upper and lower
limits. The upper limit is 3,2 km/h higher than the highest point on the trace within 1 s of the given time. The
lower limit is 3,2 km/h lower than the lowest point on the trace within 1 s of the given time. Speed variations
greater than the tolerances (such as can occur during gear changes) are acceptable provided they occur for
less than 2 s on any occasion. Speeds lower than those prescribed are acceptable provided the motorcycle
is operated at maximum available power during such occurrences. Figure 2 shows the range of acceptable
speed tolerances for typical points.
Apart from these exceptions the deviations of the roller speed from the set speed of the cycles shall meet the
requirements described above. If not, the test results shall not be used for the further analysis and the run
shall be repeated.
Key
X time
Y speed
1 1 s
2 3,2 km/h
a
Allowable range.
Figure 2 — Drivers trace, allowable range

4.4.2 Gearshift prescriptions
4.4.2.1 Test motorcycles with automatic transmission
Motorcycles equipped with transfer cases, multiple sprockets, etc., shall be tested in the manufacturer's
recommended configuration for street or highway use.
All tests shall be conducted with automatic transmissions in “drive” (highest gear). Automatic clutch-torque
converter transmissions may be shifted as manual transmissions at the option of the manufacturer.
Idle modes shall be run with automatic transmissions in “drive” and the wheels braked.
Automatic transmissions shall shift automatically through the normal sequence of gears.
The deceleration modes shall be run in gear using brakes or throttle as necessary to maintain the desired
speed.
4.4.2.2 Test motorcycles with manual transmission
4.4.2.2.1 Mandatory requirements
4.4.2.2.1.1 Step 1 — Calculation of shift speeds
Upshift speeds ( v and v ) in km/h during acceleration phases shall be calculated in accordance
12→ ii1
with Formulae (1) and (2).
 P 
  
n
19,
 
 
 
m 75
 
k
ve0,,57530 1 sn nn  (1)
  

12 idle idle
ndv
 
  
 P 
  
n
19,
 
   
m 75 1
 
k
ve0,575 3 sn n , in21 to g (2)
  

ii1 idle iddle
ndv
 
i
  
where
i is the gear number (≥2);
ng is the total number of forward gears;
P is the rated power, in kW;
n
m is the kerb mass, in kg;
k
−1
n is the idling speed, in min ;
idle
−1
s is the rated engine speed, in min ;
−1
ndv is the ratio between engine speed, in min , and motorcycle speed, in km/h, in gear i.
i
Downshift speeds (v ) in km/h during cruise or deceleration phases in gear 4 (4th gear) to ng shall be
ii1
calculated in accordance with Formula (3).

 P 
  
n
19,
 
   

m 75 1
 
k
ve0,575 3 sn n , in4 to g (3)
  

ii1 idle iddle
ndv
 
i2
  
where
i is the gear number (≥4);
ng is the total number of forward gears;
P is the rated power, in kW;
n
m is the kerb mass, in kg;
k
−1
n is the idling speed, in min ;
idle
−1
s is the rated engine speed, in min ;
−1
ndv is the ratio between engine speed, in min , and motorcycle speed, in km/h, in gear i−2.
i−2
The downshift speed from gear 3 to gear 2 ( v ) shall be calculated in accordance with Formula (4).
32→
 P 
  
n
19,
 
   

m 75
 k 
ve0,,57530 1 sn nn  (4)

 
32 idle idle
ndv
 

  
where
P is the rated power, in kW;
n
m is the kerb mass, in kg;
k
−1
n is the idling speed, in min ;
idle
−1
s is the rated engine speed, in min ;
−1
ndv is the ratio between engine speed, in min , and motorcycle speed, in km/h, in gear 1.
The downshift speed from gear 2 to gear 1 ( v ) shall be calculated in accordance with Formula (5).
21→
vs00, 3 nn  (5)

 
21 idle idle
ndv
−1
where ndv is the ratio between engine speed, in min , and motorcycle speed, in km/h, in gear 2.
Since the cruise phases are defined by the phase indicator, slight speed increases could occur and it can be
meaningful to apply an upshift. The upshift speeds ( v , v and v ) in km/h during cruise phases
12→ 23→ ii1
can be calculated in accordance with Formulae (6) to (8).
vs00, 3 nn  (6)

 
12 idle idle
ndv
P
 
  
n
19, 
 
 
m 75
 k 
ve0,,57530 1 sn nn  (7)

 

23 idle idle
ndv
 
  
 P 
  
n
19, 
 
 
m 75
 
k
ve0,5753 sn n ,tin31o g (8)
  

ii1 idle iddle
ndv
 
i1
  
The results of shift speeds shall be mathematically rounded to the first place of the decimal point.

4.4.2.2.1.2 Step 2 — Gear choice for each cycle sample
In order to avoid different interpretations about acceleration, deceleration, cruise, and stop phases,
corresponding indicators are added to the motorcycle speed pattern as integral parts of the cycles (see
Tables 2 to 25).
The appropriate gear for each sample shall then be calculated according to the motorcycle speed ranges
resulting from the shift speed formulae [Formulae (1) to (8)] and these phase indicators for the cycle parts
appropriate for the test motorcycle as follows:
— gear choice for stop phases
For the last 5 s of a stop phase, the gear lever shall be set to gear 1 and the clutch shall be disengaged. For
the previous part of a stop phase, the gear lever shall be set to neutral or the clutch shall be disengaged.
— gear choice for acceleration phases:
— gear 1, if vv ;
12
— gear 2, if vv v ;
1223
— gear 3, if vv v ;
2334
— gear 4, if vv v ;
3445
— gear 5, if vv v ;
4556
— gear 6, if vv ;
56
— gear choice for deceleration or cruise phases:
— gear 1, if vv ;
21
— gear 2, if vv ;
32
— gear 3, if vv v ;
3243
— gear 4, if vv v ;
4354
— gear 5, if vv v ;
5465
— gear 6, if vv .
45
The clutch shall be disengaged, if
a) the motorcycle speed drops below 10 km/h,
b) the engine speed drops below n + 0,03 × (s – n ), or
idle idle
c) there is a risk of engine stalling during cold start phase.
4.4.2.2.1.3 Step 3 — Corrections according to additional requirements
The gear choice has then to be modified according to the following requirements.
a) There shall be no gearshift at a transition from an acceleration phase to a deceleration phase. The gear
that was used for the last second of the acceleration phase shall be kept for the following deceleration
phase unless the speed drops below a downshift speed.
b) There shall be no upshifts or downshifts by more than one gear, except from gear 2 to neutral during
decelerations down to stop.(Example: Gear 4→4→4→4→3→3→3→3→1→1→1→1 will be replaced by gear
4→4→4→4→3→3→3→3→2→1→1→1.)
c) Upshifts or downshifts for up to 4 s are replaced by the gear before, if the gears before and after are
identical. (Examples: Gear 2→3→3→3→2 will be replaced by gear 2→2→2→2→2; gear 4→3→3→3→3→4
will be replaced by gear 4→4→4→4→4→4.)
In the cases of consecutive circumstances, the gear used longer takes over. (Example: Gear
2→2→2→3→3→3→2→2→2→2→3→3→3 will be replaced by 2→2→2→2→2→2→2→2→2→2→3→3→3.)
If used for the same time, dominate a series of succeeding gears with a series of preceding gears.
(Example: 2→2→2→3→3→3→2→2→2→3→3→3 will be replaced by 2→2→2→2→2→2→2→2→2→3→3→ 3.)
d) There shall be no downshift during an acceleration phase.
4.4.2.2.2 Optional provisions
The gear choice may be modified according to the following provisions.
— The use of lower gears than determined by the requirements described in 4.4.2.2.1 is permitted in any
cycle phase. Manufacturers' recommendations for gear use shall be followed, if they do not result in
higher gears than determined by the requirements described in 4.4.2.2.1.
NOTE 1 The calculation program to be found on the UN website at the URL below can be used as an aid for the gear
selection: https:// www .unece .org/ trans/ main/ wp29/ wp29wgs/ wp29grpe/ wmtc .html.
NOTE 2 Explanations of the approach and the gearshift strategy are given in Annex D
4.5 Type 2 tests
4.5.1 Application
This requirement only applies to all test motorcycles powered by a positive-ignition engine.
4.5.2 Measured gaseous pollutant
The content by volume of carbon monoxide shall be measured immediately after the type 1 test.
4.5.3 Engine test speeds
The test shall be carried out with the engine at normal idling speed and at “high idle” speed. High idle speed
−1
is defined by the manufacturer but it shall be higher than 2 000 min .
4.5.4 Gear lever position
In the case of test motorcycles with manually operated or semi-automatic shift gearboxes, the test shall be
carried out with the gear lever in the “neutral” position and with the clutch engaged. In the case of test
motorcycles with automatic-shift gearboxes, the test shall be carried out with the gear selector in either the
“neutral” or the “park” position.
4.6 Test procedures
4.6.1 Type 1 tests
4.6.1.1 Emissions tests
4.6.1.1.1 Engine starting and restarting
4.6.1.1.1.1 The engine shall be started according to the manufacturer's recommended starting procedures.
The test cycle run shall begin when the engine starts.

4.6.1.1.1.2 Test motorcycles equipped with automatic chokes shall be operated according to the
instructions in the manufacturer's operating instructions or owner's manual including choke setting and
“kick-down” from cold fast idle. If necessary, braking may be employed to keep the drive wheels from
turning.
4.6.1.1.1.3 Test motorcycles equipped with manual chokes shall be operated according to the
manufacturer's operating instructions or owner's manual. Where times are provided in the instructions, the
point for operation may be specified, within 15 s of the recommended time.
4.6.1.1.1.4 The operator may use the choke, throttle, etc. where necessary to keep the engine running.
4.6.1.1.1.5 If the manufacturer's operating instructions or owner's manual do not specify a warm engine
starting procedure, the engine (automatic and manual choke engines) shall be started by opening the
throttle about half way and cranking the engine until it starts.
4.6.1.1.1.6 If, during the cold start, the test motorcycle does not start after 10 s of cranking, or 10 cycles
of the manual starting mechanism, cranking shall cease and the reason for failure to start determined. The
revolution counter on the constant volume sampler shall be turned off and the sample solenoid valves placed
in the “standby” position during this diagnostic period. In addition, either the CVS blower shall be turned off
or the exhaust tube disconnected from the tailpipe during the diagnostic period.
4.6.1.1.1.7 If failure to start is an operational error, the test motorcycle shall be rescheduled for testing
from a cold start. If failure to start is caused by motorcycle malfunction, corrective action (following the
unscheduled maintenance provisions) of less than 30 min duration may be taken and the test continued.
The sampling system shall be reactivated at the same time cranking is started. When the engine starts, the
driving schedule timing sequence shall begin. If failure to start is caused by motorcycle malfunction and the
test motorcycle cannot be started, the test shall be voided, the motorcycle removed from the dynamometer,
corrective action taken (following the unscheduled maintenance provisions), and the motorcycle rescheduled
for test. The reason for the malfunction (if determined) and the corrective action taken shall be reported.
4.6.1.1.1.8 If the test motorcycle does not start during the hot start after 10 s of cranking, or 10 cycles
of the manual starting mechanism, cranking shall cease, the test shall be voided, the motorcycle removed
from the dynamometer, corrective action taken, and the motorcycle rescheduled for test. The reason for the
malfunction (if determined) and the corrective action taken shall be reported.
4.6.1.1.1.9 If the engine “false starts”, the operator shall repeat the recommended starting procedure
(such as resetting the choke, etc.).
4.6.1.1.2 Stalling
4.6.1.1.2.1 If the engine stalls during an idle period, the engine shall be restarted immediately and the
test continued. If the engine cannot be started soon enough to allow the test motorcycle to follow the next
acceleration as prescribed, the driving schedule indicator shall be stopped. When the test motorcycle
restarts, the driving schedule indicator shall be reactivated.
4.6.1.1.2.2 If the engine stalls during some operating mode other than idle, the driving schedule indicator
shall be stopped, the test motorcycle shall then be restarted and accelerated to the speed required at that
point in the driving schedule and the test continued. During acceleration to this point, shifting shall be
performed in accordance with 4.4.2.
4.6.1.1.2.3 If the test motorcycle will not restart within 1 min, the test shall be voided, the motorcycle
removed from the dynamometer, corrective action taken, and the motorcycle rescheduled for test. The
reason for the malfunction (if determined) and the corrective action taken shall be reported.

4.6.1.2 Drive instructions
4.6.1.2.1 The test motorcycle shall be driven with minimum throttle movement to maintain the desired
speed. No simultaneous use of brake and throttle shall be permitted.
4.6.1.2.2 If the test motorcycle cannot accelerate at the specified rate, it shall be operated with the throttle
fully opened until the roller speed reaches the value prescribed for that time in the driving schedule.
4.6.1.3 Dynamometer test runs
4.6.1.3.1 The complete dynamometer test consists of consecutive parts as described in 4.4.1.
4.6.1.3.2 The following steps shall be taken for each test.
a) Place drive wheel of test motorcycle on dynamometer without starting engine.
b) Activate motorcycle cooling fan.
c) For all test motorcycles, with the sample selector valves in the “standby” position, connect evacuated
sample collection bags to the diluted exhaust mixture and dilution air sample collection systems.
d) Start the CVS (if not already on), the sampling pumps and the temperature recorder. (The heat exchanger
of the constant volume sampler, if used, and sample lines shall be preheated to their respective operating
temperatures before the test begins.)
e) Adjust the sample flow rates to the desired flow rate and set the gas flow measuring devices to zero.
1) For gaseous bag samples, the sample flow rate shall be set to the appropriate levels.
2) For hydrocarbon samples, if necessary, the sample flow rate for the flame ionization detection (FID)
(or heated flame ionization detection (HFID) in the case of methanol-fuelled motorcycles) shall be
set to the appropriate levels.
f) Attach the flexible exhaust tube to the motorcycle tailpipe(s).
g) Start the gas flow measuring device, position the sample selector valves to direct the sample flow into
the exhaust sample bag, the dilution air sample bag, turn the key on, and start cranking the engine.
h) Put the transmission in gear;
i) Begin the initial motorcycle acceleration of the driving schedule.
j) Operate the test motorcycle according to the driving cycles specified in 4.4.1.
k) At the end of the part 1 or part 1 reduced speed in cold condition, simultaneously switch the sample
flows from the first sampling bags and samples to the second sampling bags and samples, switch off gas
flow measuring device No. 1 and start gas flow measuring device No. 2.
l) In case of class 3 motorcycles capable of running part 3 of the WMTC, at the end of part 2, simultaneously
switch the sample flows from the second sampling bags and samples to the third sampling bags and
samples, switch off gas flow measuring device No. 2 and, start gas flow measuring device No. 3.
m) Before starting a new part, record the measured roll or shaft revolutions and reset the counter or switch
to a second counter. As soon as possible, transfer the exhaust and dilution air samples to the analytical
system and process the samples according to 4.7.1.1, obtaining a stabilized reading of the exhaust bag
sample on all analysers within 30 min of the end of the sample collection phase of the test.
n) Turn the engine off 2 s after the end of the last part of the test.
o) Immediately after the end of the sample period, turn off the cooling fan.

p) Turn off the constant volume sampler (CVS).
q) Disconnect the exhaust tube from the test motorcycle tailpipe(s) and remove the motorcycle from the
dynamometer.
r) For comparison and analysis reasons, second-by-second emissions (diluted gas) data may be monitored
as well as the bag results. Type 2 tests
4.6.1.4 Conditions of measurement
4.6.2.1.1 The type 2 test specified in 4.5 shall be measured immediately after the type 1 test with the
engine at normal idling speed and at high idle.
4.6.2.1.2 The following parameters shall be measured and recorded at normal idling speed and at high
idle speed:
a) the carbon monoxide content by volume of the exhaust gases emitted;
b) the carbon dioxide content by volume of the exhaust gases emitted;
c) the engine speed during the test, including any tolerances;
d) the engine oil temperature at the time of the test.
4.6.1.5 Sampling exhaust gases
4.6.2.2.1 The exhaust outlets shall be provided with an air-tight extension, so that the sampling probe
used to collect exhaust gases may be inserted into the exhaust outlet at least 60 cm, without increasing
the back pressure of more than 125 mm H O, and without disturbance of the test motorcycle running. The
shape of this extension shall however be chosen in order to avoid, at the location of the sampling probe, any
appreciable dilution of exhaust gases in the air. Where a motorcycle is equipped with an exhaust system
having multiple outlets, either these shall be joined to a common pipe or the content of carbon monoxide
shall be collected from each of them, the result of the measurement being reached from the arithmetical
average of these contents.
4.6.2.2.2 The concentrations in CO (c ) and CO (c ) shall be determined from the measuring instrument
CO 2 CO2
readings or recordings, by use of appropriate calibration curves. The results shall be corrected according to
4.7.2.
4.7 Analysis of results
4.7.1 Type 1 tests
4.7.1.1 Gaseous exhaust emission and fuel consumption analysis
4.7.1.1.1 Analysis of the samples contained in the bags
The analysis shall begin as soon as possible and in any event not later than 30 min after the end of the tests,
in order to determine
— the concentrations of hydrocarbons, carbon monoxide, nitrogen oxides, and carbon dioxide in the sample
of dilution air contained in bag(s) B, and
— the concentrations of hydrocarbons, carbon monoxide, nitrogen oxides, and carbon dioxide in the sample
of diluted exhaust mixture contained in bag(s) A.

4.7.1.2 Weighting of results
4.7.1.2.1 In case of repeated measurements, the emission results in g/km and the fuel consumption in
L/100 km obtained by the calculation method described in ISO 6460-1 are averaged for each cycle part.
4.7.1.2.2 The (average) result of part 1 or part 1 reduced speed is named R , the (average) result of part 1
in hot condition or part 1 reduced speed in hot condition is named R , the (average) result of part 2 or part
1hot
2 reduced speed is named R and the (average) result of part 3 or part 3 reduced speed is named R . Using
2, 3
these emission results in g/km and the fuel consumption in L/100 km; the final result R, depending on the
motorcycle class as defined in 4.3, shall be calculated by means of Formulae (9) to (11).
Class 1
RRwRw (9)
11 11hothot
Class 2
RRwRw (10)
11 22
Class 3
RRwRwRw (11)
11 22 33
4.7.1.2.3 For each pollutant, the carbon dioxide emission and the fuel consumption the weightings shown
in Table 1 shall be used.
Table 1 — Weighting factors for the final emission and fuel consumption results
Motorcycle
Cycle Weighting
class
Part 1, cold w 30 %
Class 1
Part 1, hot w 70 %
1hot
Part 1, cold w 30 %
Class 2
Part 2, hot w 70 %
Part 1, cold w 25 %
Class 3 Part 2, hot w 50 %
Part 3, hot w 25 %
4.7.2 Type 2 tests
4.7.2.1 The corrected concentration for carbon monoxide (c and c in per cent volume) is
CO,ec2 CO,ec4
calculated in accordance with Formula (12).
cc (12)
CO,ec4 CO,e
cc
CO,e CO2,e
4.7.2.2 The concentration in c measured according to 4.6.2.2 need not be corrected if the total of the
CO,e
concentrations measured, c + c is at least 15 for four-stroke engines.
CO,e CO2,e,
4.8 Driving cycles for type 1 tests
Key
X time, s
Y speed, km/h
1 part 1
2 part 1, reduced speed
Figure 3 — Cycle part 1
Key
X time, s
Y speed, km/h
1 part 2
2 part 2, reduced speed
Figure 4 — Cycle part 2 for motorcycle classes 2 and 3

Key
X time, s
Y speed, km/h
1 part 3
2 part 3, reduced speed
Figure 5 — Cycle part 3 for motorcycle class 3

Table 2 — Cycle part 1, reduced speed for motorcycle classes 1 and 2-1, 1 s to 180 s
Roller Phase indicators Roller Phase indicators Roller Phase indicators
Time Time Time
speed speed speed
s s s
Stop Acc Cruise Dec Stop Acc Cruise Dec Stop Acc Cruise Dec
km/h km/h km/h
0 0,0 X  41 28,7 X 82 32,9 X
1 0,0 X  42 27,9 X 83 34,7 X
2 0,0 X  43 27,4 X 84 34,8 X
3 0,0 X  44 27,3 X 85 34,8 X
4 0,0 X  45 27,3 X 86 34,9 X
5 0,0 X  46 27,4 X 87 35,4 X
6 0,0 X  47 27,5 X 88 36,2 X
7 0,0 X  48 27,6 X 89 37,1 X
8 0,0 X  49 27,6 X 90 38,0 X
9 0,0 X  50 27,6 X 91 38,7 X
10 0,0 X  51 27,8 X 92 38,9 X
11 0,0 X  52 28,1 X 93 38,9 X
12 0,0 X  53 28,5 X 94 38,8 X
13 0,0 X  54 28,9 X 95 38,5 X
14 0,0 X  55 29,2 X 96 38,1 X
15 0,0 X  56 29,4 X 97 37,5 X
16 0,0 X  57 29,7 X 98 37,0 X
17 0,0 X  58 30,0 X 99 36,7 X
18 0,0 X  59 30,5 X 100 36,5 X
19 0,0 X  60 30,6  X 101 36,5 X
20 0,0 X  61 29,6  X 102 36,6 X
21 0,0 X  62 26,9  X 103 36,8 X
22 1,0 X 63 23,0  X 104 37,0 X
23 2,6 X 64 18,6  X 105 37,1 X
24 4,8 X 65 14,1  X 106 37,3 X
25 7,2 X 66 9,3  X 107 37,4 X
26 9,6 X 67 4,8  X 108 37,5 X
27 12,0 X 68 1,9  X 109 37,4 X
28 14,3 X 69 0,0 X  110 36,9  X
29 16,6 X 70 0,0 X  111 36,0  X
30 18,9 X 71 0,0 X  112 34,8  X
31 21,2 X 72 0,0 X  113 31,9  X
32 23,5 X 73 0,0 X  114 29,0  X
33 25,6 X 74 1,7 X 115 26,9  X
34 27,1 X 75 5,8 X 116 24,7 X
35 28,0 X 76 11,8 X 117 25,4 X
36 28,7 X 77 17,3 X 118 26,4 X
37 29,2 X 78 22,0 X 119 27,7 X
38 29,8 X 79 26,2 X 120 29,4 X
39 30,3 X 80 29,4 X 121 31,2 X
40 29,6 X 81 31,1 X 122 33,0 X

Table 2 — (continued)
Roller Phase indicators Roller Phase indicators Roller Phase indicators
Time Time Time
speed speed speed
s s s
Stop Acc Cruise Dec Stop Acc Cruise Dec Stop Acc Cruise Dec
km/h km/h km/h
123 34,4 X 143 29,7  X 163 0,0 X
124 35,2 X 144 28,1  X 164 0,0 X
125 35,4  X 145 25,0  X 165 0,0 X
126 35,2  X 146 20,3  X 166 0,0 X
127 34,7  X 147 15,0  X 167 0,0 X
128 33,9  X 148 9,7  X 168 0,0 X
129 32,4  X 149 5,0  X 169 0,0 X
130 29,8  X 150 1,6  X 170 0,0 X
131 26,1  X 151 0,0 X  171 0,0 X
132 22,1  X 152 0,0 X  172 0,0 X
133 18,6  X 153 0,0 X  173 0,0 X
134 16,8 X 154 0,0 X  174 0,0 X
135 17,7 X 155 0,0 X  175 0,0 X
136 21,1 X 156 0,0 X  176 0,0 X
137 25,4 X 157 0,0 X  177 0,0 X
138 29,2 X 158 0,0 X  178 0,0 X
139 31,6 X 159 0,0 X  179 0,0 X
140 32,1  X 160 0,0 X  180 0,0 X
141 31,6  X 161 0,0 X
142 30,7  X 162 0,0 X
Table 3 — Cycle part 1, reduced speed for motorcycle classes 1 and 2–1, 181 s to 360 s
Roller Phase indicators Roller Phase indicators Roller Phase indicators
Time Time Time
speed speed speed
s s s
Stop Acc Cruise Dec Stop Acc Cruise Dec Stop Acc Cruise Dec
km/h km/h km/h
181 0,0 X  196 37,8 X 211 46,9 X
182 0,0 X  197 39,6 X 212 47,2 X
183 0,0 X  198 41,3 X 213 47,8 X
184 0,0 X  199 43,3 X 214 48,4 X
185 0,4 X 200 45,1 X 215 48,9 X
186 1,8 X 201 47,5 X 216 49,2 X
187 5,4 X 202 49,0 X 217 49,6 X
188 11,1 X 203 50,0 X 218 49,9 X
189 16,7 X 204 49,5 X 219 50,0 X
190 21,3 X 205 48,8 X 220 49,8 X
191 24,8 X 206 47,6 X 221 49,5 X
192 28,4 X 207 46,5 X 222 49,2 X
193 31,8 X 208 46,1 X 223 49,3 X
194 34,6 X 209 46,1 X 224 49,4 X
195 36,3 X 210 46,6 X 225 49,4 X

Table 3 — (continued)
Roller Phase indicators Roller Phase indicators Roller Phase indicators
Time Time Time
speed speed speed
s s s
Stop Acc Cruise Dec Stop Acc Cruise Dec Stop Acc Cruise Dec
km/h km/h km/h
226 48,6 X 267 0,5 X 308 25,7 X
227 47,8 X 268 2,9 X 309 25,5 X
228 47,0 X 269 8,2 X 310 25,7 X
229 46,9 X 270 13,2 X 311 26,4 X
230 46,6 X 271 17,8 X 312 27,3 X
231 46,6 X 272 21,4 X 313 28,1 X
232 46,6 X 273 24,1 X 314 27,9  X
233 46,9 X 274 26,4 X 315 26,0  X
234 46,4 X 275 28,4 X 316 22,7  X
235 45,6 X 276 29,9 X 317 19,0  X
236 44,4 X 277 30,5 X 318 16,0  X
237 43,5 X 278 30,5 X 319 14,6 X
238 43,2 X 279 30,3 X 320 15,2 X
239 43,3 X 280 30,2 X 321 16,9 X
240 43,7 X 281 30,1 X 322 19,3 X
241 43,9 X 282 30,1 X 323 22,0 X
242 43,8  X 283 30,1 X 324 24,6 X
243 43,0  X 284 30,2 X 325 26,8 X
244 40,9  X 285 30,2 X 326 27,9 X
245 36,9  X 286 30,2 X 327 28,0 X
246 32,1  X 287 30,2 X 328 27,7 X
247 26,6  X 288 30,5 X 329 27,1 X
248 21,8  X 289 31,0 X 330 26,8 X
249 17,2  X 290 31,9 X 331 26,6 X
250 13,7  X 291 32,8 X 332 26,8 X
251 10,3  X 292 33,7 X 333 27,0 X
252 7,0  X 293 34,5 X 334 27,2 X
253 3,5  X 294 35,1 X 335 27,4 X
254 0,0 X  295 35,5 X 336 27,5 X
255 0,0 X  296 35,6 X 337 27,7 X
256 0,0 X  297 35,4 X 338 27,9 X
257 0,0 X  298 35,0 X 339 28,1 X
258 0,0 X  299 34,0 X 340 28,3 X
259 0,0 X  300 32,4 X 341 28,6 X
260 0,0 X  301 30,6 X 342 29,1 X
261 0,0 X  302 29,0 X 343 29,6 X
262 0,0 X  303 27,8 X 344 30,1 X
263 0,0 X  304 27,2 X 345 30,6 X
264 0,0 X  305 26,9 X 346 30,8 X
265 0,0 X  306 26,5 X 347 30,8 X
266 0,0 X  307 26,1 X 348 30,8 X

Table 3 — (continued)
Roller Phase indicators Roller Phase indicators Roller Phase indicators
Time Time Time
speed speed speed
s s s
Stop Acc Cruise Dec Stop Acc Cruise Dec Stop Acc Cruise Dec
km/h km/h km/h
349 30,8 X 353 30,8 X 357 30,8 X
...