ISO 27145-2:2012

INTERNATIONAL ISO
STANDARD 27145-2
First edition
2012-08-15
Road vehicles — Implementation of
World-Wide Harmonized On-Board
Diagnostics (WWH-OBD) communication
requirements —
Part 2:
Common data dictionary
Véhicules routiers — Mise en application des exigences de
communication pour le diagnostic embarqué harmonisé à l'échelle
mondiale (WWH-OBD) —
Partie 2: Dictionnaire de données communes

Reference number
©
ISO 2012
©  ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

Contents Page
Foreword . iv
0  Introduction . v
1  Scope . 1
2  Normative references . 2
3  Terms, definitions and abbreviated terms . 2
3.1  Terms and definitions . 2
3.2  Abbreviated terms . 4
4  Conventions . 5
5  Document overview . 5
6  Common data dictionary requirements . 7
6.1  Data range layout . 7
6.2  Diagnostic trouble code (DTC) range layout . 7
7  Data identifier and routine identifier data record requirements . 8
7.1  Data identifier and routine identifier definitions . 8
7.2  DID and RID data record definition . 8
8  Diagnostic trouble code definition . 14
8.1  Overview . 14
8.2  SAE J2012-DA and SAE J1939-73 DTCs . 15
9  Presentation layer requirements . 18
Annex A (normative) DID (PID, MID, ITID) and RID supported definition . 19
Annex B (normative) WWH-OBD server/ECU supported mandatory DID . 22
Annex C (informative) GTR WWH-OBD emissions system parameters . 23
Annex D (normative) GTR WWH-OBD DTCExtendedDataRecord content . 30
Annex E (informative) Definition guidelines for new DID (PID, MID, ITID) assignments . 31
Bibliography . 34

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 27145-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3,
Electrical and electronic equipment.
This first edition of ISO 27145-2 cancels and replaces ISO/PAS 27145-2:2006, which has been technically
revised.
ISO 27145 consists of the following parts, under the general title Road vehicles — Implementation of World-
Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements:
 Part 1: General information and use case definition
 Part 2: Common data dictionary
 Part 3: Common message dictionary
 Part 4: Connection between vehicle and test equipment
The following parts are under preparation:
 Part 6: External test equipment
iv © ISO 2012 – All rights reserved

0 Introduction
0.1 Overview
The ISO 27145 series includes the communication between the vehicle's on-board diagnostics (OBD)
systems and external test equipment within the scope of the World-Wide Harmonized On-Board Diagnostics
Global Technical Regulations (WWH-OBD GTR).
It has been established in order to apply the unified diagnostic services (specified in ISO 14229-1) to WWH-
OBD systems.
The ISO 27145 series includes the communication between the vehicle's WWH-OBD systems and external
(off-board) "generic" test equipment within the scope of the country-specific regulatory requirements.
To achieve this, it is based on the Open Systems Interconnection (OSI) Basic Reference Model in
ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers. Where
mapped on this model, the services specified by ISO 27145 are divided into
 diagnostic services (layer 7), specified in ISO 27145-3 with reference to ISO 14229-1,
 presentation layer (layer 6), specified in this part of ISO 27145 with reference to SAE J1930-DA,
SAE J1939 Companion Spreadsheet (SPNs), SAE J1939-73:2010, Appendix A (FMIs), SAE J1979-DA
and SAE J2012-DA,
 session layer services (layer 5), specified in ISO 14229-2,
 transport layer services (layer 4), specified in ISO 27145-4 with reference to ISO 13400-2, ISO 15765-2
and ISO 15765-4,
 network layer services (layer 3), specified in ISO 27145-4 with reference to ISO 15765-4, ISO 15765-2
and ISO 13400-2,
 data link layer (layer 2), specified in ISO 27145-4 with reference to ISO 11898-1, ISO 11898-2,
ISO 15765-4, ISO 13400-3 and IEEE 802.3, and
 physical layer (layer 1), specified in ISO 27145-4 with reference to ISO 11898-1, ISO 11898-2,
ISO 15765-4, ISO 13400-3 and IEEE 802.3,
in accordance with Table 1.
Table 1 — WWH-OBD specification reference applicable to the OSI layers
Applicability OSI seven layer WWH-OBD reference
Application (layer 7) ISO 14229-1, ISO 27145-3
This part of ISO 27145,
Presentation (layer 6) SAE J1930-DA, SAE J1939 Companion Spreadsheet (SPNs),
SAE J1939-73:2010, Appendix A (FMIs), SAE J1979-DA, SAE J2012-DA
Seven layers
according to
Session (layer 5) ISO 14229-2
ISO/IEC 7498-1
Transport (layer 4)
and
ISO 15765-2 DoCAN, ISO 13400-2 DoIP
ISO/IEC 10731
ISO 15765-4 DoCAN TCP and IP
Network (layer 3)
ISO 27145-4
ISO 11898-1 CAN DLL,
Data link (layer 2)
ISO 13400-3 DoIP,
ISO 11898-2 CAN HS,
IEEE 802.3
ISO 15765-4 DoCAN
Physical (layer 1)
0.2 SAE document reference concept
ISO 27145 makes reference to several SAE documents which contain the relevant terms, data and diagnostic
trouble code (DTC) definitions.
ISO 27145-2 defines a common data dictionary for the ISO 27145 series, according to the definitions in the
following documents (see Figure 1):
 SAE J1930-DA: this digital annex contains all standardized naming objects, terms and abbreviations.
 SAE J1939 Companion Spreadsheet and SAE J1939-73: SAE J1939 Companion Spreadsheet indexes
names for suspect parameter numbers (SPNs), which provide an alternative presentation format for
SAE J2012-DA DTCs. SPNs are combined with failure mode indicators (FMIs) to form the full alternative
presentation. FMIs are described in SAE J1939-73:2010, Appendix A.
NOTE The SAE J1939 Companion Spreadsheet is a document which supplements the SAE J1939 family of
standards and contains SPNs and PGNs.
 SAE J1979-DA: this digital annex contains all standardized data items such as data identifiers (DIDs), test
identifiers (TIDs), monitor identifiers (MIDs) and info type identifiers (ITIDs).
 SAE J2012-DA: this digital annex contains all standardized data items such as DTC definitions and failure
type byte (FTB) definitions.
ISO 27145-2
WWH-OBD
common data dictionary
1 2
SAE J1930-DA
SAE J1939
digital annex of
SAE J1939-73:2010
SAE J2012-DA
[Companion
SAE J1979-DA electrical /electronic
[Appendix A]
digital annex of
Spreadsheet]
digital annex of E/E systems diagnostic
diagnostic trouble
diagnostic test modes terms, definitions,
code definitions
abbreviations and
acronyms
Key
1 SAE digital annexes: data definitions
2 SAE J1939 series of documents: DTC definitions
Figure 1 — SAE digital annex document reference
0.3 SAE digital annex revision procedure
New regulatory requirements drive new in-vehicle technology to lower emissions, improve safety, etc. It is
important to standardize new technology-related OBD monitor data and diagnostic trouble codes in order to
support the external (off-board) "generic" test equipment. All relevant information is proposed by the
automotive industry represented by members of the appropriate SAE task force.
This part of ISO 27145 references a "Change request form" for use with new data items to be defined by the
SAE task force for standardization. It is intended that the standardized data items be defined in
SAE J1930-DA, SAE J1979-DA, SAE J2012-DA and SAE J1939. It is intended that the documents be
published on the SAE store website once the information has been balloted and approved.
vi © ISO 2012 – All rights reserved

The revision request forms and instructions for updating the registers to ISO 27145 can be obtained on the
following data registration websites.
 For SAE J1930-DA: http://www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS7
The column entitled "Resources" shows a document with the title: J1930-
DA_Revision_Request_Form.doc. Double click on the name to download the document with the filename:
"SAE_J1930-DA_Revision_Request_Form.doc".
 For SAE J1939: http://www.sae.org/
Search "J1939 Request", select "J1939 Request Processing Group", and select " J1939 Request
Processing Form and Guidelines".
 For SAE J1979-DA: http://www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS14
The column entitled "Resources" shows a document with the title: J1979-
DA_Revision_Request_Form.doc. Double click on the name to download the document with the filename:
"SAE_J1979-DA_Revision_Request_Form.doc".
 For SAE J2012-DA: http://www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS9
The column entitled "Resources" shows a document with the title: J2012-
DA_Revision_Request_Form.doc. Double click on the name to download the document with the filename:
"SAE_J2012-DA_Revision_Request_Form.doc".
It is intended that the revision request form be filled out with the request.
It is intended that e-mails with completed revision request forms as attachments be sent to:
E-mail: saej1930@sae.org
E-mail: saej1979@sae.org
E-mail: saej2012@sae.org
E-mail: saej1939@sae.org
INTERNATIONAL STANDARD ISO 27145-2:2012(E)

Road vehicles — Implementation of World-Wide Harmonized
On-Board Diagnostics (WWH-OBD) communication
requirements —
Part 2:
Common data dictionary
1 Scope
This part of ISO 27145 defines all regulatory data elements of the ISO 27145 series. The data elements are
used to provide the external test equipment with the diagnostic status of the vehicle on-board diagnostics
(VOBD) system in the vehicle. All data elements are communicated with the unified diagnostic services as
defined in ISO 27145-3. The data elements are diagnostic trouble codes (DTCs), data identifiers (DIDs) and
routine identifiers (RIDs). The mapping from parameter identifiers (PIDs), monitor identifiers (MIDs) and info
type identifiers (ITIDs) is described in this part of ISO 27145.
If new legislated WWH-OBD GTR modules are established, it is intended that ISO 27145 be applicable with
possible extensions, which can be included in this part of ISO 27145, can be specified as enhancements of
the SAE Digital Annexes or can e
...