ISO 3613:2021
(Main)Metallic and other inorganic coatings — Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys — Test methods
Metallic and other inorganic coatings — Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys — Test methods
This document specifies methods for the determination of — the presence of colourless chromate conversion coatings, — the presence of hexavalent chromium in colourless and coloured coatings on zinc or cadmium or aluminium-zinc (mass fraction of aluminium: 55 %, within a range of 54 % to 56 % mass fraction) and zinc-aluminium (mass fraction of aluminium: 5 %) alloys, — the total chromium content per unit area on zinc and cadmium, — the mass per unit area of both colourless and coloured coatings, — the satisfactory adhesion of chromate conversion coatings, and — the quality of chromate coatings. These methods are applicable to — colourless and coloured chromate conversion coatings containing trivalent and hexavalent chromium in varying proportions and produced by either chemical or electrochemical processes, and — chromate coatings that are free from any supplementary coatings, such as oil, water or solvent-based polymers or wax.
Revêtements métalliques et autres revêtements inorganiques — Couches de conversion au chromate sur zinc, cadmium et alliages d'aluminium-zinc et de zinc-aluminium — Méthodes d'essai
Le présent document spécifie des méthodes permettant de déterminer: — la présence de couches de conversion au chromate incolores; — la présence de chrome hexavalent dans les couches incolores ou colorées sur zinc, cadmium ou alliages d’aluminium-zinc (fraction massique d’aluminium de 55 %, dans une plage de 54 % à 56 %) et de zinc-aluminium (fraction massique d’aluminium de 5 %); — la teneur totale en chrome par unité de surface sur zinc et cadmium; — la masse par unité de surface des couches incolores et colorées; — le degré d’adhérence des couches de conversion au chromate; — la qualité des couches de chromate. Ces méthodes s’appliquent: — aux couches de conversion au chromate incolores et colorées contenant du chrome trivalent et hexavalent en diverses proportions et produites par un procédé chimique ou électrochimique; — aux couches de chromate exemptes de tout revêtement supplémentaire tel que huile, polymère à base d’eau ou de solvant, ou cire.
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 3613
Fourth edition
2021-05
Metallic and other inorganic
coatings — Chromate conversion
coatings on zinc, cadmium,
aluminium-zinc alloys and zinc-
aluminium alloys — Test methods
Revêtements métalliques et autres revêtements inorganiques —
Couches de conversion au chromate sur zinc, cadmium et alliages
d'aluminium-zinc et de zinc-aluminium — Méthodes d'essai
Reference number
©
ISO 2021
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Reagents . 2
5 Apparatus . 3
6 Test methods . 4
6.1 General . 4
6.2 Test for the presence of a colourless chromate coating on zinc . 4
6.3 Test for the presence of a colourless chromate coating on zinc and cadmium . 4
6.4 Test for the presence of a colourless chromate coating on zinc-aluminium (mass
fraction of aluminium: 5 %) alloys . 5
6.5 Test for the presence of hexavalent chromium in both colourless and coloured
chromate coatings . 5
6.5.1 General. 5
6.5.2 Test method employing test solution C 1 . 5
6.5.3 Test method employing alternative test solution C 2 (destructive) . 5
6.5.4 Expression of results . 7
6.5.5 Calibration of spectrophotometer . 7
6.6 Determination of hexavalent chromium content of coloured chromate coatings . 8
6.6.1 Preparation of calibration graph . 8
6.6.2 Blank test . 8
6.6.3 Determination . 8
6.6.4 Expression of results . 8
6.7 Determination of total chromium content of coloured chromate coatings . 9
6.7.1 Preparation of calibration graph . 9
6.7.2 Blank test . 9
6.7.3 Determination . 9
6.7.4 Expression of results . 9
6.8 Determination of mass per unit area of both colourless and coloured chromate
coatings by gravimetric method . 9
6.9 Test for adhesion by abrasion . 9
6.10 Quality evaluation test of chromate layers on zinc and cadmium surfaces .10
7 Test report .10
Bibliography .11
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 262, Metallic and other inorganic coatings, including for corrosion protection and corrosion testing of
metals and alloys, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 3613:2010), which has been technically
revised. The main changes compared with the previous edition are as follows:
— Table 1 has been revised;
— analysis method described in 6.5 was aligned with the method described in IEC 62321-7-1;
— procedure for the preparation of test solution C 2 in 4.3.2 has been revised and a second standard
solution has been added;
— limiting time has been amended in 6.1;
— procedure for testing with test solution C 2 has been revised in 6.5.2;
— description of the calibration of spectrophotometer has been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
Introduction
This document specifies methods for the qualitative determination of the presence of chromate
conversion coatings as well as the total chromium content of chromate conversion coatings.
The application of very thin, colourless, practically invisible chromate conversion coatings is frequently
called “passivation”, while the application of thicker, coloured chromate conversion coatings is called
“chromating”. The term “passivation” is not correct, as it does not conform to the ISO 2080 designation,
and is therefore deprecated.
Chromate conversion coatings are based on a solution containing Cr(VI). Both the process solution and
the coating contain hexavalent chromium. The term passivation is nowadays often used for Cr(VI)-free
coatings replacing chromate conversion coatings. Products containing Cr(VI) are not allowed within
EU and processes using Cr(VI) are strictly regulated.
INTERNATIONAL STANDARD ISO 3613:2021(E)
Metallic and other inorganic coatings — Chromate
conversion coatings on zinc, cadmium, aluminium-zinc
alloys and zinc-aluminium alloys — Test methods
WARNING — This document calls for the use of substances and/or procedures that can be injurious
to health if adequate safety measures are not taken. This document does not address any health
hazards, safety or environmental matters associated with its use. It is the responsibility of the
user of this document to establish appropriate health, safety and environmentally acceptable
practices and take suitable actions for any national and international regulations.
1 Scope
This document specifies methods for the determination of
— the presence of colourless chromate conversion coatings,
— the presence of hexavalent chromium in colourless and coloured coatings on zinc or cadmium or
aluminium-zinc (mass fraction of aluminium: 55 %, within a range of 54 % to 56 % mass fraction)
and zinc-aluminium (mass fraction of aluminium: 5 %) alloys,
— the total chromium content per unit area on zinc and cadmium,
— the mass per unit area of both colourless and coloured coatings,
— the satisfactory adhesion of chromate conversion coatings, and
— the quality of chromate coatings.
These methods are applicable to
— colourless and coloured chromate conversion coatings containing trivalent and hexavalent
chromium in varying proportions and produced by either chemical or electrochemical processes,
and
— chromate coatings that are free from any supplementary coatings, such as oil, water or solvent-
based polymers or wax.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3892, Conversion coatings on metallic materials — Determination of coating mass per unit area —
Gravimetric methods
ISO 4520, Chromate conversion coatings on electroplated zinc and cadmium coatings
IEC 60068-2-30, Environmental testing — Part 2-30: Tests — Test Db: Damp heat, cyclic (12 h + 12 h cycle)
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Reagents
Use only reagents of recognized analytical grade and distilled water or water of equivalent purity,
unless otherwise specified, for analysis.
4.1 Test solution A (see 6.2).
Dissolve 1 g of diphenylcarbazide in a mixture of 20 ml of acetone, 60 ml of glacial acetic acid and 40 ml
of distilled water contained in a beaker. Add 15 ml of concentrated hydrochloric acid
...
NORME ISO
INTERNATIONALE 3613
Quatrième édition
2021-05
Revêtements métalliques et autres
revêtements inorganiques — Couches
de conversion au chromate sur zinc,
cadmium et alliages d'aluminium-zinc
et de zinc-aluminium — Méthodes
d'essai
Metallic and other inorganic coatings — Chromate conversion
coatings on zinc, cadmium, aluminium-zinc alloys and zinc-
aluminium alloys — Test methods
Numéro de référence
©
ISO 2021
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Réactifs . 2
5 Appareillage . 3
6 Méthodes d’essai . 4
6.1 Généralités . 4
6.2 Essai de détection d’une couche de chromate incolore sur zinc . 5
6.3 Essai de détection d’une couche de chromate incolore sur zinc et cadmium . 5
6.4 Essai de détection d’une couche de chromate incolore sur des alliages de zinc-
aluminium (fraction massique d’aluminium de 5 %). 5
6.5 Essai de détection de chrome hexavalent dans les couches de chromate incolores
et colorées . 6
6.5.1 Généralités . 6
6.5.2 Méthode d’essai utilisant la solution d’essai C 1 . 6
6.5.3 Méthode d’essai utilisant l’autre solution d’essai C 2 (essai destructif) . 6
6.5.4 Expression des résultats . 7
6.5.5 Étalonnage du spectrophotomètre . 7
6.6 Détermination de la teneur en chrome hexavalent des couches de chromate colorées. 8
6.6.1 Préparation de la courbe d’étalonnage. 8
6.6.2 Essai à blanc . 8
6.6.3 Détermination . 8
6.6.4 Expression des résultats . 9
6.7 Détermination de la teneur totale en chrome des couches de chromate colorées . 9
6.7.1 Préparation de la courbe d’étalonnage. 9
6.7.2 Essai à blanc . 9
6.7.3 Détermination . 9
6.7.4 Expression des résultats .10
6.8 Détermination de la masse par unité de surface des couches de chromate, colorées
et incolores, par gravimétrie .10
6.9 Essai d’adhérence par abrasion .10
6.10 Essai d’évaluation qualitative des couches de chromate sur zinc et cadmium .10
7 Rapport d’essai .10
Bibliographie .11
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion
de l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www .iso .org/ iso/ fr/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 107, Revêtements métalliques et
autres revêtements inorganiques, en collaboration avec le comité technique CEN/TC 262, Revêtements
métalliques et inorganiques, incluant ceux pour la protection contre la corrosion et les essais de corrosion
des métaux et alliages, du Comité européen de normalisation (CEN), conformément à l’Accord de
coopération technique entre l’ISO et le CEN (Accord de Vienne).
Cette quatrième édition annule et remplace la troisième édition (ISO 3613:2010), qui a fait l’objet d’une
révision technique. Les principales modifications par rapport à l’édition précédente sont les suivantes:
— révision du Tableau 1;
— harmonisation de la méthode d’analyse décrite en 6.5 avec la méthode décrite dans l’IEC 62321-7-1;
— révision du mode opératoire de préparation de la solution d’essai C 2 indiqué en 4.3.2 et ajout d’une
deuxième solution étalon;
— modification des délais indiqués en 6.1;
— révision du mode opératoire d’essai utilisant la solution d’essai C 2 indiqué en 6.5.2;
— ajout d’une description de l’étalonnage du spectrophotomètre.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés
Introduction
Le présent document spécifie des méthodes permettant de déterminer la présence, d’un point de vue
qualitatif, de couches de conversion au chromate ainsi que leur teneur totale en chrome.
L’application de couches de conversion au chromate très minces, incolores, pratiquement invisibles, est
fréquemment appelée «passivation», tandis que l’application de couches de conversion au chromate
plus épaisses, colorées, est souvent appelée «chromatation». Le terme «passivation» est incorrect, car
non conforme à la désignation de l’ISO 2080, son emploi est donc déconseillé.
Les couches de conversion au chromate sont obtenues à partir d’une solution contenant du Cr(VI). Tant
la solution de traitement que le revêtement contiennent du chrome hexavalent. Désormais, le terme
«passivation» est fréquemment utilisé pour désigner les revêtements exempts de Cr(VI) qui remplacent
les couches de conversion au chromate. Les produits contenant du Cr(VI) ne sont pas autorisés au sein
de l’UE et les procédés impliquant cette substance sont rigoureusement réglementés.
NORME INTERNATIONALE ISO 3613:2021(F)
Revêtements métalliques et autres revêtements
inorganiques — Couches de conversion au chromate sur
zinc, cadmium et alliages d'aluminium-zinc et de zinc-
aluminium — Méthodes d'essai
AVERTISSEMENT — Le présent document nécessite l’utilisation de substances et/ou de modes
opératoires pouvant s’avérer préjudiciables à la santé si des mesures de sécurité adéquates ne
sont pas prises. Le présent document ne traite ni des dangers pour la santé ni des questions
de sécurité ou d’environnement associées à son utilisation. Il incombe à l’utilisateur du présent
document d’établir des pratiques appropriées acceptables en matière de santé, de sécurité et
d’environnement et de prendre des mesures adéquates pour satisfaire aux réglementations
nationales et internationales.
1 Domaine d’application
Le présent document spécifie des méthodes permettant de déterminer:
— la présence de couches de conversion au chromate incolores;
— la présence de chrome hexavalent dans les couches incolores ou colorées sur zinc, cadmium ou
alliages d’aluminium-zinc (fraction massique d’aluminium de 55 %, dans une plage de 54 % à 56 %)
et de zinc-aluminium (fraction massique d’aluminium de 5 %);
— la teneur totale en chrome par unité de surface sur zinc et cadmium;
— la masse par unité de surface des couches incolores et colorées;
— le degré d’adhérence des couches de conversion au chromate;
— la qualité des couches de chromate.
Ces méthodes s’appliquent:
— aux couches de conversion au chromate incolores et colorées contenant du chrome trivalent et
hexavalent en diverses proportions et produites par un procédé chimique ou électrochimique;
— aux couches de chromate exemptes de tout revêtement supplémentaire tel que huile, polymère à
base d’eau ou de solvant, ou cire.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s’applique (y compris les
éventuels amendements).
ISO 3892, Couches de conversion sur matériaux métalliques — Détermination de la masse de revêtement
par unité de surface — Méthodes gravimétriques
ISO 4520, Couches de conversion au chromate sur les dépôts électrolytiques de zinc et de cadmium
IEC 60068-2-30, Ess
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.