ETSI TS 101 889-1 V1.1.1 (2002-08)

SLOVENSKI STANDARD
01-april-2004
Harmonizacija telekomunikacij in internetnega protokola prek omrežij (TIPHON), 3.
izdaja - Specifikacija tehnološke ustreznosti - Profil TIPHON za ITU-T H.248 - 1. del:
Izjava o skladnosti izvedbe protokola (PICS) - Proforma specifikacija
Telecommunications and Internet Protocol Harmonization Over Networks (TIPHON)
Release 3; Technology Compliance Specification; TIPHON profile for ITU-T H.248; Part
1: Protocol Implementation Conformance Statement (PICS) proforma specification
Ta slovenski standard je istoveten z: TS 101 889-1 Version 1.1.1
ICS:
33.020 Telekomunikacije na splošno Telecommunications in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

Technical Specification
Telecommunications and Internet Protocol
Harmonization Over Networks (TIPHON) Release 3;
Technology Compliance Specification;
TIPHON profile for IUT-T H.248;
Part 1: Protocol Implementation Conformance
Statement (PICS) proforma specification

2 ETSI TS 101 889-1 V1.1.1 (2002-08)

Reference
DTS/TIPHON-06017-1
Keywords
H.248, IP, PICS, supplementary service,
telephony, testing, VoIP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
editor@etsi.fr
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2002.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI TS 101 889-1 V1.1.1 (2002-08)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .6
1 Scope.7
2 References.7
3 Definitions and abbreviations.9
3.1 Definitions.9
3.2 Abbreviations.9
4 Conformance to this PICS proforma specification.9
Annex A (normative): PICS proforma for ITU-T Recommendation H.248.1 as specified in
TS 101 885 .10
A.1 Guidance for completing the PICS proforma.10
A.1.1 Purposes and structure.10
A.1.2 Abbreviations and conventions .10
A.1.3 Instructions for completing the PICS proforma.12
A.2 Identification of the implementation .13
A.2.1 Date of the statement.13
A.2.2 Implementation Under Test (IUT) identification .13
A.2.3 System Under Test (SUT) identification.13
A.2.4 Product supplier.13
A.2.5 Client (if different from product supplier).14
A.2.6 PICS contact person .14
A.3 PICS/System Conformance Statement (SCS) .15
A.4 Identification of the protocol.15
A.5 Global statement of conformance.15
A.6 General Remarks.16
A.6.1 TIPHON interfaces.16
A.6.2 General mapping between H.248.1 and TIPHON parameters.16
A.6.3 General structure of the H.248.1 messages .17
A.7 Major functional capabilities.17
A.7.1 Role of the Implementation Under Test (IUT).17
A.7.2 General properties of the IUT.18
A.7.3 Transactions.19
A.7.4 Contexts.19
A.7.5 Terminations.20
A.7.6 Commands applying to Terminations.20
A.7.7 Descriptors applying to Commands .21
A.8 Basic signalling procedures.22
A.8.1 Transaction procedures.22
A.8.2 Context procedures.22
A.8.3 Command procedures.23
A.9 Protocol messages sent by the IUT .24
A.9.1 H.248/MEGACO message PDU.24
A.9.2 Transactions.25
A.9.2.1 Transaction Request.25
A.9.2.2 Transaction Reply.25
A.9.2.3 Transaction Pending.25
ETSI
4 ETSI TS 101 889-1 V1.1.1 (2002-08)
A.9.2.4 Transaction ResponseAck.25
A.9.3 Contexts.26
A.9.3.1 Action Request.26
A.9.3.2 Action Reply.26
A.9.4 Commands.27
A.9.4.1 Command Requests.27
A.9.4.1.1 Add Command Request .27
A.9.4.1.2 Modify Command Request.27
A.9.4.1.3 Substract Command Request.28
A.9.4.1.4 Move Command Request.28
A.9.4.1.5 AuditValue Command Request.28
A.9.4.1.6 AuditCapabilities Command Request.28
A.9.4.1.7 Notify Command Request.29
A.9.4.1.8 ServiceChange Command Request.29
A.9.4.2 Command Replies.29
A.9.4.2.1 Add Command Reply.29
A.9.4.2.2 Modify Command Reply.30
A.9.4.2.3 Subtract Command Reply .30
A.9.4.2.4 Move Command Reply .31
A.9.4.2.5 AuditValue Command Reply.31
A.9.4.2.6 AuditCapabilities Command Reply.32
A.9.4.2.7 Notify Command Reply.32
A.9.4.2.8 Service Change Command Reply .32
A.9.5 Descriptors.33
A.9.5.1 Media Descriptor.33
A.9.5.2 Termination State Descriptor.33
A.9.5.3 Stream Descriptor.34
A.9.5.4 Local Descriptor.34
A.9.5.5 Remote Descriptor.34
A.9.5.6 Local Control Descriptor .35
A.9.5.7 ServiceChange Descriptor.35
A.9.5.8 Statistics Descriptor.36
A.9.5.9 Error Descriptor.36
A.10 Support of annexes/Packages.37
A.10.1 Annex C: Tags for Media Stream Properties.37
A.10.2 Annex D: Transport over IP .37
A.10.2.1 Transport over IP/UDP .37
A.10.2.2 Transport over IP/TCP.38
A.10.3 Annex E: Basic Packages .38
A.10.4 Annex L: Error Code descriptions.39
A.10.5 Additional annexes and Packages .39
A.11 Timers and Parameters .40
A.11.1 Timers.40
A.11.2 IUT Parameters.40
A.12 Support of specific procedures for the TIPHON interfaces according to the TIPHON release 3
profile .41
A.12.1 Specific PICS for TIPHON interface N2 according to TS 101 885 .41
A.12.2 Specific PICS for TIPHON interface N3 according to TS 101 885 .41
History .42

ETSI
5 ETSI TS 101 889-1 V1.1.1 (2002-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Project Telecommunications and Internet Protocol
Harmonization Over Networks (TIPHON).
The present document is part 1 of a multi-part deliverable covering Conformance Testing for TIPHON Release 3;
TIPHON profile for ITU-T recommendation H.248.1 [20], as identified below:
Part 1: "Protocol Implementation Conformance Statement (PICS) proforma specification";
Part 2: "Test Suite Structure and Test Purposes (TSS&TP) specification";
Part 3: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
proforma specification".
ETSI
6 ETSI TS 101 889-1 V1.1.1 (2002-08)
Introduction
To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and
options have been implemented for a telecommunication specification. Such a statement is called an Implementation
Conformance Statement (ICS).
Figure 1 shows the relationship of the present document with other TIPHON release 3 deliverables.

TR 101 301
Release 3: Scope & Definition
TR 102 008
Definition of Terms
Transport Plane
Service Capabilities
TR 101 311 TS 101 878
Architecture & Reference
TS 101 314
configurations
Implementer's
Protocol
TS 101 882 TS 101 315
guide
Framework
TS 101 883 TS 101 884 TS 101 885
H.323 profile SIP profile H.248 profile
TS 101 890 TS 101 889 TS 101 804 TS 102 027
-1, -2, -3 -1, -2 -1, -2, -3 -1, -2
SIP,
H.225 PICS,
H.245 PICS,
H248 PICS,
TSS&TPs,
TSS&TPs, TSS&TPs,
TSS&TPs
ATS & PIXIT
ATS & PIXIT ATS & PIXIT
Figure 1: Relationship with other TIPHON release 3 documents
ETSI
7 ETSI TS 101 889-1 V1.1.1 (2002-08)
1 Scope
The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for the
audiovisual and multimedia systems Infrastructure of audiovisual services - Communication procedures, Gateway
control protocol, ITU-T Recommendation H.248.1 [20] in compliance with the relevant requirements specified in
TS 101 885 [1] and in accordance with the relevant guidance given in ISO/IEC 9646-7 [22].
The supplier of a protocol implementation which is claimed to conform to TIPHON mapping to H.248.1 [20] is
required to complete a copy of the PICS proforma provided in annex A of the present document and is required to
provide the information necessary to identify both the supplier and the implementation.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
[1] ETSI TS 101 885: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Mapping; Technology Mapping of TIPHON reference point N
to H.248/MEGACO protocol".
[2] ETSI TR 101 301: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Release Definition; TIPHON Release 3 Definition".
[3] ETSI TR 102 008: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Terms and Definitions ".
[4] ETSI TR 101 311: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Service Independent requirements definition; Transport Plane".
[5] ETSI TS 101 878: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Service Capability Definition; Service Capabilities for a simple call".
[6] ETSI TS 101 314: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Abstract Architecture and Reference Points Definition; Network
Architecture and Reference Points".
[7] ETSI TS 101 882: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Protocol Framework Definition; General (meta-protocol)".
[8] ETSI TS 101 315: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Functional entities, information flow and reference point definitions;
Guidelines for application of TIPHON functional architecture to inter-domain services".
[9] ETSI TS 101 883: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Mapping; Implementation of TIPHON architecture using
H.323".
[10] ETSI TS 101 884: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Mapping; Implementation of TIPHON architecture using SIP".
[11] ETSI TS 101 890-1: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Compliance Specifications; TIPHON profile for ITU-T H.245;
Part 1: Protocol Implementation Conformance Statement (PICS) proforma specification".
ETSI
8 ETSI TS 101 889-1 V1.1.1 (2002-08)
[12] ETSI TS 101 890-2: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Compliance Specifications; TIPHON profile for ITU-T H.245;
Part 2: Test Suite Structure and Test Purposes (TSS&TP) specification".
[13] ETSI TS 101 890-3: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Compliance Specifications; TIPHON profile for ITU-T H.245;
Part 3: Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for
Testing (PIXIT) proforma specification".
[14] ETSI TS 101 889-2: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology Compliance Specification; TIPHON profile for ITU-T H.248;
Part 2: Test Suite Structure and Test Purposes (TSS&TP) specification".
[15] ETSI TS 101 804-1: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology compliance specifications; Part 1: Revision/Update of H.225.0
Protocol Implementation Conformance Statement (PICS) proforma specification for Terminal,
Gatekeeper and Gateway".
[16] ETSI TS 101 804-2: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology compliance specifications; Part 2: H.225.0 conformance test
specifications; Test Suite Structure and Test Purposes (TSS&TP) specification for Terminal,
Gatekeeper and Gateway".
[17] ETSI TS 101 804-3: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON) Release 3; Technology compliance specifications; Part 3: H.225.0 conformance test
specifications; Abstract Test Suite (ATS) and PIXIT proforma specification for Terminal,
Gatekeeper and Gateway".
[18] ETSI TS 102 027-1: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON); Technology Compliance Specification; Draft IETF SIP RFC2543bis-04; Part 1: Test
Suite Structure and Test Purposes (TSS&TP) specification;".
[19] ETSI TS 102 027-2: "Telecommunications and Internet Protocol Harmonization Over Networks
(TIPHON); Technology Compliance Specification; Draft IETF SIP RFC2543bis-04; Part 2:
Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing
(PIXIT) proforma specification".
[20] ITU-T Recommendation H.248.1.1: "Gateway control protocol: Version 1".
[21] ISO/IEC 9646-1 (1994): "Information technology - Open Systems Interconnection - Conformance
testing methodology and framework - Part 1: General concepts".
[22] ISO/IEC 9646-7 (1995): "Information technology - Open Systems Interconnection - Conformance
testing methodology and framework - Part 7: Implementation Conformance Statements".
[23] ETSI TS 101 882: "Protocol Framework Telecommunications and Internet Protocol
Harmonization Over Networks (TIPHON) Release 3; Protocol Framework Definition; General
(meta-protocol)".
ETSI
9 ETSI TS 101 889-1 V1.1.1 (2002-08)
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
- terms defined in ITU-T Recommendation H.248.1 [20];
- terms defined in ISO/IEC 9646-1 [21] and in ISO/IEC 9646-7 [22].
In particular, the following terms defined in ISO/IEC 9646-1 [21] apply:
Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system
claimed to conform to a given specification, stating which capabilities have been implemented
NOTE: The PICS can take several forms: protocol PICS, profile PICS, profile specific PICS, information object
PICS, etc.
Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ICS Implementation Conformance Statement
IUT Implementation Under Test
MG Media Gateway
MGC Media Gateway Controller
PDU Protocol Data Unit
PICS Protocol Implementation Conformance Statement
SCS System Conformance Statement
SUT System Under Test
4 Conformance to this PICS proforma specification
If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be
technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and
ordering of the proforma items.
A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with
the guidance for completion given in clause A.1.
ETSI
10 ETSI TS 101 889-1 V1.1.1 (2002-08)
Annex A (normative):
PICS proforma for ITU-T Recommendation H.248.1 as
specified in TS 101 885
Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that
users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its
intended purposes and may further publish the completed PICS.
A.1 Guidance for completing the PICS proforma
A.1.1 Purposes and structure
The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the
requirements defined in ITU-T Recommendation H.248.1 may provide information about the implementation in a
standardized manner.
The PICS proforma is subdivided into clauses for the following categories of information:
• guidance for completing the PICS proforma;
• identification of the implementation;
• identification of the protocol;
• global statement of conformance;
• general remarks;
• roles and major capabilities;
• basic procedures;
• coding supported by the IUT;
• support of annexes/packages;
• timers and parameters
A.1.2 Abbreviations and conventions
The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the
guidelines presented in ISO/IEC 9646-7.
Item column
The item column contains a number which identifies the item in the table.
Item description column
The item description column describes in free text each respective item (for example parameters, timers, etc.). It
implicitly means "is < item description > supported by the implementation?".
ETSI
11 ETSI TS 101 889-1 V1.1.1 (2002-08)
Status column
The following notations, defined in ISO/IEC 9646-7, are used for the status column:
m mandatory - the capability is required to be supported;
o optional - the capability may be supported or not;
n/a not applicable - in the given context, it is impossible to use the capability;
x prohibited (excluded) - there is a requirement not to use this capability in the given context;
o.i qualified optional - for mutually exclusive or selectable options from a set. "i" is an integer which
identifies a unique group of related optional items and the logic of their selection which is defined
immediately following the table;
c.i conditional - the requirement on the capability ("m", "o", "x" or "n/a") depends on the support of
other optional or conditional items. "i" is an integer identifying a unique conditional status
expression which is defined immediately following the table;
i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is
requested from the supplier.
Reference column
The reference column makes reference to ITU-T Recommendation H.248.1 except where explicitly stated otherwise.
Support column
The supplier of the implementation shall fill in the support column. The following common notations, defined in
ISO/IEC 9646-7, are used for the support column:
Y or y supported by the implementation;
N or n not supported by the implementation;
N/A, n/a or no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional
status).
If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able
to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall
enter the unique reference to a conditional expression, preceded by "?" (for example ?3). This expression shall be given
in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which
refers to a single profile and which takes the value TRUE if and only if that profile is to be used.
EXAMPLE: ?3: IF prof1 THEN Y ELSE N.
It is also possible to provide a comment to an answer in the space provided at the bottom of the table.
NOTE: As stated in ISO/IEC 9646-7, support for a received PDU requires the ability to parse all valid parameters
of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant.
Support for a parameter on a PDU means that the semantics of that parameter are supported.
Values allowed column
The values allowed column contains the type, the list, the range, or the length of values allowed. The following
notations are used:
• range of values:  < min value > . < max value >:
- example: 5 . 20.
ETSI
12 ETSI TS 101 889-1 V1.1.1 (2002-08)
• List of values:  < value1 >, < value2 >, ., < valueN >:
- example: 2, 4, 6, 8, 9;
- example: '1101'B, '1011'B, '1111'B;
- example: '0A'H, '34'H, '2F'H.
• List of named values: < name1 >(< val1 >), < name2 >(< val2 >), ., < nameN >(< valN >:
- example: reject(1), accept(2).
• Length:   size (< min size > . < max size >):
- example: size (1 . 8).
Values supported column
The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the
ranges of values supported by the implementation shall be indicated.
References to items
For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists,
used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character "/",
followed by the item number in the table. If there is more than one support column in a table, the columns are
discriminated by letters (a, b, etc.), respectively.
EXAMPLE 1: A.5/4 is the reference to the answer of item 4 in table 5 of annex A.
EXAMPLE 2: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in
table 6 of annex A.
Prerequisite line
A prerequisite line takes the form: Prerequisite: < predicate >.
A prerequisite line after a clause or table title indicates that the whole clause or the whole table is not required to be
completed if the predicate is FALSE.
A.1.3 Instructions for completing the PICS proforma
The supplier of the implementation shall complete the PICS proforma in each of the spaces provided. In particular, an
explicit answer shall be entered, in each of the support or supported column boxes provided, using the notation
described in clause A.1.2.
If necessary, the supplier may provide additional comments in space at the bottom of the tables, or separately on sheets
of paper.
More detailed instructions are given at the beginning of the different clauses of the PICS proforma.
ETSI
13 ETSI TS 101 889-1 V1.1.1 (2002-08)
A.2 Identification of the implementation
Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test
(SUT)) should be filled in so as to provide as much detail as possible regarding version numbers and configuration
options.
The product supplier information and client information should both be filled in if they are different.
A person who can answer queries regarding information supplied in the PICS should be named as the contact person.
A.2.1 Date of the statement
...............................................................................................................................................................................................
A.2.2 Implementation Under Test (IUT) identification
IUT name:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
IUT version:
...............................................................................................................................................................................................
A.2.3 System Under Test (SUT) identification
SUT name:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
Hardware configuration:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
...............................................................................................................................................................................................
Operating system:
...............................................................................................................................................................................................
A.2.4 Product supplier
Name:
...............................................................................................................................................................................................
Address:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
...............................................................................................................................................................................................
ETSI
14 ETSI TS 101 889-1 V1.1.1 (2002-08)
Telephone number:
...............................................................................................................................................................................................
Facsimile number:
...............................................................................................................................................................................................
E-mail address:
...............................................................................................................................................................................................
Additional information:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
...............................................................................................................................................................................................
A.2.5 Client (if different from product supplier)
Name:
...............................................................................................................................................................................................
Address:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
...............................................................................................................................................................................................
Telephone number:
...............................................................................................................................................................................................
Facsimile number:
...............................................................................................................................................................................................
E-mail address:
...............................................................................................................................................................................................
Additional information:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
A.2.6 PICS contact person
(A person to contact if there are any queries concerning the content of the PICS)
Name:
...............................................................................................................................................................................................
Telephone number:
...............................................................................................................................................................................................
ETSI
15 ETSI TS 101 889-1 V1.1.1 (2002-08)
Facsimile number:
...............................................................................................................................................................................................
E-mail address:
...............................................................................................................................................................................................
Additional information:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
...............................................................................................................................................................................................
A.3 PICS/System Conformance Statement (S
...