EN 17878-1:2024/prA1
(Amendment)District heating pipes - Factory made flexible pipe systems with a lower temperature profile - Part 1: Classification, general requirements and test methods
- Abstract
This document specifies classification, general requirements and test methods for flexible, factory made, buried district heating pipe systems.
This document is intended to be used only in conjunction with EN 17878-2 or EN 17878-3, as applicable.
This document is applicable to a maximum operating temperature of 80 °C and a maximum operating design pressure up to 1,0 MPa.
The pipe systems are designed for a service life of at least 50 years. For pipe systems with plastic service pipes, the respective temperature profiles are specified in EN 17878-2:2024 and EN 17878-3:2024.
For the transport of other liquids, for example potable water, additional requirements can be applicable.
- Status
- Not Published
- Publication Date
- 20-Sep-2028
- Technical Committee
- CEN/TC 107 - Pre-fabricated district heating pipe systems
- Drafting Committee
- CEN/TC 107/WG 10 - Flexible pipe systems for district heating
- Current Stage
- 4020 - Submission to enquiry - Enquiry
- Start Date
- 29-Oct-2026
- Due Date
- 10-Jun-2027
- Completion Date
- 29-Oct-2026
Relations
- Effective Date
- 22-Jul-2026
Get Certified
Connect with accredited certification bodies for this standard
Institut za varilstvo d.o.o. (Welding Institute)
Slovenia's leading welding institute since 1952. ISO 3834, EN 1090, pressure equipment certification, NDT personnel, welder qualification. Only IIW Au
Sponsored listings
Frequently Asked Questions
EN 17878-1:2024/prA1 is a draft published by the European Committee for Standardization (CEN). Its full title is "District heating pipes - Factory made flexible pipe systems with a lower temperature profile - Part 1: Classification, general requirements and test methods". This standard covers: This document specifies classification, general requirements and test methods for flexible, factory made, buried district heating pipe systems. This document is intended to be used only in conjunction with EN 17878-2 or EN 17878-3, as applicable. This document is applicable to a maximum operating temperature of 80 °C and a maximum operating design pressure up to 1,0 MPa. The pipe systems are designed for a service life of at least 50 years. For pipe systems with plastic service pipes, the respective temperature profiles are specified in EN 17878-2:2024 and EN 17878-3:2024. For the transport of other liquids, for example potable water, additional requirements can be applicable.
This document specifies classification, general requirements and test methods for flexible, factory made, buried district heating pipe systems. This document is intended to be used only in conjunction with EN 17878-2 or EN 17878-3, as applicable. This document is applicable to a maximum operating temperature of 80 °C and a maximum operating design pressure up to 1,0 MPa. The pipe systems are designed for a service life of at least 50 years. For pipe systems with plastic service pipes, the respective temperature profiles are specified in EN 17878-2:2024 and EN 17878-3:2024. For the transport of other liquids, for example potable water, additional requirements can be applicable.
EN 17878-1:2024/prA1 is classified under the following ICS (International Classification for Standards) categories: 23.040.07 - Pipeline and its parts for district heat. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 17878-1:2024/prA1 has the following relationships with other standards: It is inter standard links to EN 17878-1:2024. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 17878-1:2024/prA1 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2027
Cevi za daljinsko ogrevanje - Tovarniško izdelani gibki cevni sistemi z nižjim
temperaturnim profilom - 1. del: Klasifikacija, splošne zahteve in preskusne
metode - Dopolnilo A1
District heating pipes - Factory made flexible pipe systems with a lower temperature
profile - Part 1: Classification, general requirements and test methods
Fernwärmerohre - Werkmäßig hergestellte flexible Rohrsysteme mit einem niedrigeren
Temperaturprofil - Teil 1: Klassifikation, allgemeine Anforderungen und Prüfungen
Tuyaux de chauffage urbain - Système de tuyaux flexibles préisolés - Partie 1 :
Classification, exigences générales et méthodes d'essai
Ta slovenski standard je istoveten z: EN 17878-1:2024/prA1
ICS:
23.040.07 Cevovodi za daljinsko Pipeline and its parts for
ogrevanje in njihovi deli district heat
23.040.20 Cevi iz polimernih materialov Plastics pipes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 17878-1:2024
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2026
ICS 23.040.07
English Version
District heating pipes - Factory made flexible pipe systems
with a lower temperature profile - Part 1: Classification,
general requirements and test methods
Tuyaux de chauffage urbain - Système de tuyaux Fernwärmerohre - Werkmäßig hergestellte flexible
flexibles préisolés - Partie 1 : Classification, exigences Rohrsysteme mit einem niedrigeren Temperaturprofil
générales et méthodes d'essai - Teil 1: Klassifikation, allgemeine Anforderungen und
Prüfungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 107.
This draft amendment A1, if approved, will modify the European Standard EN 17878-1:2024. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17878-1:2024/prA1:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to Clause 2, “Normative References” . 4
2 Modification to 3.1, “Terms and definitions” . 4
3 Addition to 5.5, “Casing” . 4
4 Addition of Annex A “Utilization of reworked material and PE recyclate for the casing
of flexible district heating pipes according to this document” . 4
5 Addition to the Bibliography . 7
European foreword
This document (EN 17878-1:2024/prA1:2026) has been prepared by Technical Committee CEN/TC 107
“District heating and cooling systems”, the secretariat of which is held by DS.
This document is currently submitted to the CEN Enquiry.
1 Modification to Clause 2, “Normative References”
Add the following reference:
“EN 14541-1, Plastics pipes and fittings - Utilisation of thermoplastic materials in a circular economy -
Part 1: Vocabulary”
2 Modification to 3.1, “Ter
...



