ASTM F885-84(2001)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 885 – 84 (Reapproved 2001)
Standard Specification for
Envelope Dimensions for Bronze Globe Valves NPS ¼ to 2
This standard is issued under the fixed designation F 885; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
TABLE 1 Brazed End Connection Dimensions
1. Scope
1.1 This specification provides standard dimensions for
Valve Size Depth of Diameter of Socket, in. (mm)
small bronze globe valves (NPS ¼ to 2) installed in shipboard
− NPS Socket, in.
Minimum Maximum
(mm)
piping systems.
¼ ⁄64 (7) 0.540 (13.72) 0.543 (13.79)
1.2 This specification covers valves of a nominal pipe size
3 5
⁄8 ⁄16 (8) 0.675 (17.15) 0.678 (17.22)
from NPS ¼ to 2 with threaded and brazed end connections.
½ ⁄8 (10) 0.840 (21.34) 0.843 (21.41)
3 13
The valves are in accordance with MSS-SP80, Class 200.
⁄4 ⁄32 (10) 1.050 (26.67) 1.053 (26.74)
1 ⁄16 (11) 1.315 (33.40) 1.318 (33.48)
1¼ ⁄2 (13) 1.660 (42.16) 1.663 (42.24)
2. Referenced Documents
1½ ⁄8 (16) 1.900 (48.26) 1.905 (48.39)
2.1 ASTM Standards: 21
2 ⁄32 (17) 2.375 (60.33) 2.380 (60.45)
B2.1 Pipe Threads (Except Dryseal)
2.2 Manufacturer’s Standardization Society of the Valve
and Fittings Industry Standard:
SP80 Bronze Gate, Globe, Angle and Check Valves
4. Dimensions
4.1 Valve dimensions for both threaded- and brazed-type
3. Materials and Manufacture
end connections are provided in Fig. 1.
3.1 Threaded end connections shall be in accordance with
ANSI B2.1. Brazed end connections shall be in accordance
5. Tolerances
with Table 1.
5.1 A plus or minus tolerance of ⁄32 in. (0.8 mm) shall be
allowed on all dimensions that do not have a maximum or
minimum specified.
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery and Piping Systems. 6. Keywords
Current edition approved May 25, 1984. Published September 1984.
2 6.1 brazedconnection;bronzeglobevalve;envelopedimen-
Available from American National Standards Institute, 25 W. 43rd St., 4th
sion; globe valve; marine technology; ship
Floor, New York, NY 10036.
AvailablefromManufacturer’sStandardizationSocietyoftheValveandFitting
Industry, 1815 N. Fort Myer Dr., Arlington, VA 22209.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
F 885 – 84 (2001)
TABLE 1 Continued
AB C D E
Valve Size −NPS End to End, Pipe Centerline to Valve Maximum
...