ASTM D1183-03(2019)

ASTM D1183-03(2019) is a standard published by ASTM International. Its full title is "Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions". This standard covers: SIGNIFICANCE AND USE 4.1 These practices provide information on the resistance to cyclic laboratory aging. SCOPE 1.1 These practices cover the determination of the resistance of adhesives to cyclic accelerated service conditions by exposing bonded specimens to conditions of high and low temperatures and high and low relative humidities. The extent of degradation is determined from changes in strength properties as a result of exposure to the test conditions (Note 1). It is recognized that no accelerated procedure for degrading materials correlates perfectly with actual service conditions, and that no single or small group of laboratory test conditions will simulate all actual service conditions. Consequently, care must be exercised in the interpretation and use of data obtained in this practice. The test condition, the number of cycles of the test condition to be used, the particular strength property to be used to determine the extent of degradation, and whether test specimens or test panels are to be used, are specified in the material specification. Note 1: These practices/conditions are intended for use with specimens described in the approved ASTM strength test methods for adhesives as follows: Test Methods D897, D903, D906, D950, D1002, D1062, and Test Method D1344. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE 4.1 These practices provide information on the resistance to cyclic laboratory aging. SCOPE 1.1 These practices cover the determination of the resistance of adhesives to cyclic accelerated service conditions by exposing bonded specimens to conditions of high and low temperatures and high and low relative humidities. The extent of degradation is determined from changes in strength properties as a result of exposure to the test conditions (Note 1). It is recognized that no accelerated procedure for degrading materials correlates perfectly with actual service conditions, and that no single or small group of laboratory test conditions will simulate all actual service conditions. Consequently, care must be exercised in the interpretation and use of data obtained in this practice. The test condition, the number of cycles of the test condition to be used, the particular strength property to be used to determine the extent of degradation, and whether test specimens or test panels are to be used, are specified in the material specification. Note 1: These practices/conditions are intended for use with specimens described in the approved ASTM strength test methods for adhesives as follows: Test Methods D897, D903, D906, D950, D1002, D1062, and Test Method D1344. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D1183-03(2019) is classified under the following ICS (International Classification for Standards) categories: 83.180 - Adhesives. The ICS classification helps identify the subject area and facilitates finding related standards.

ASTM D1183-03(2019) has the following relationships with other standards: It is inter standard links to ASTM D906-20, ASTM D950-03(2020)e1, ASTM D1002-10(2019), ASTM D903-98(2017), ASTM D906-98(2017), ASTM D897-08(2016), ASTM D907-12a, ASTM D907-12, ASTM D907-11a, ASTM D906-98(2011), ASTM D950-03(2011), ASTM D907-11, ASTM D903-98(2010), ASTM D897-08, ASTM D1062-08. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ASTM D1183-03(2019) is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.