ASTM B952/B952M-19(2024)

ASTM B952/B952M-19(2024) is a technical specification published by ASTM International. Its full title is "Standard Specification for Zinc Alloys in Ingot Form for Spin Casting". This standard covers: ABSTRACT This specification covers four zinc alloys in ingot form, namely: Spin Casting Alloy SC-A, Spin Casting Alloy SC-B, Spin Casting Alloy SC-C, and ZA-73, for remelting for the manufacture of spin castings. The alloys may be made by any approved process, shall be of uniform quality, and shall be free from dross or other harmful contamination. The ingots shall conform to the chemical composition limits prescribed for aluminum, magnesium, copper, iron, lead, cadmium, tin, nickel, and zinc. Chemical analysis requirements for determination and for verification (if needed) of chemical composition are detailed. SCOPE 1.1 This specification covers zinc alloys in ingot form for remelting for the manufacture of Spin Castings as specified and designated, as shown in Table 1. Seven alloy compositions are specified, designated as follows: Common Traditional UNS Spin Casting Alloy SC-A ... Z35550 Spin Casting Alloy SC-B ... Z35551 Spin Casting Alloy SC-C ... Z35534 Spin Casting Alloy SC-D HJ10 Z35547 Spin Casting Alloy SC-E HJ20 Z35548 Spin Casting Alloy SC-F HJ40 Z35552 ZA-73 ... Z36500 1.2 Zinc alloys #2, #3, #5, and ZA-8 specified in Specification B240 are also used in the spin casting process. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT This specification covers four zinc alloys in ingot form, namely: Spin Casting Alloy SC-A, Spin Casting Alloy SC-B, Spin Casting Alloy SC-C, and ZA-73, for remelting for the manufacture of spin castings. The alloys may be made by any approved process, shall be of uniform quality, and shall be free from dross or other harmful contamination. The ingots shall conform to the chemical composition limits prescribed for aluminum, magnesium, copper, iron, lead, cadmium, tin, nickel, and zinc. Chemical analysis requirements for determination and for verification (if needed) of chemical composition are detailed. SCOPE 1.1 This specification covers zinc alloys in ingot form for remelting for the manufacture of Spin Castings as specified and designated, as shown in Table 1. Seven alloy compositions are specified, designated as follows: Common Traditional UNS Spin Casting Alloy SC-A ... Z35550 Spin Casting Alloy SC-B ... Z35551 Spin Casting Alloy SC-C ... Z35534 Spin Casting Alloy SC-D HJ10 Z35547 Spin Casting Alloy SC-E HJ20 Z35548 Spin Casting Alloy SC-F HJ40 Z35552 ZA-73 ... Z36500 1.2 Zinc alloys #2, #3, #5, and ZA-8 specified in Specification B240 are also used in the spin casting process. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B952/B952M-19(2024) is classified under the following ICS (International Classification for Standards) categories: 77.150.60 - Lead, zinc and tin products. The ICS classification helps identify the subject area and facilitates finding related standards.

ASTM B952/B952M-19(2024) has the following relationships with other standards: It is inter standard links to ASTM B952/B952M-19. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ASTM B952/B952M-19(2024) is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.