ASTM B468-10(2020)

ASTM B468-10(2020) is a technical specification published by ASTM International. Its full title is "Standard Specification for Welded UNS N08020 Alloy Tubes". This standard covers: ABSTRACT This specification covers welded UNS N08020, N08024, and N08026 alloy boiler, heat exchanger, and condenser tubes for general corrosion-resisting and low- or high-temperature service. Tubing shall be made from flat-rolled stock by an automatic welding process with no addition of filler metal. Subsequent to welding and prior to final heat treatment, the material shall be cold-worked in either the wed metal only, or in both the weld and base metal. Tubing of UNS N0820 alloy shall be furnished in the stabilized-annealed condition, Tubing of UNS N0824 alloy shall be furnished in the annealed condition. Tubing of UNS N0826 alloy shall be furnished in the solution-annealed condition. The material shall conform to the composition limits specified. The material shall conform to the mechanical property requirements for tensile strength, yield strength and elongation. Flattening and flange tests shall be made on each end of one tube per lot. SCOPE 1.1 This specification2 covers welded UNS N08020 alloy boiler, heat exchanger, and condenser tubes for general corrosion-resisting and low- or high-temperature service. 1.2 This specification covers tubes 1/8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Table 2 of Specification B751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT This specification covers welded UNS N08020, N08024, and N08026 alloy boiler, heat exchanger, and condenser tubes for general corrosion-resisting and low- or high-temperature service. Tubing shall be made from flat-rolled stock by an automatic welding process with no addition of filler metal. Subsequent to welding and prior to final heat treatment, the material shall be cold-worked in either the wed metal only, or in both the weld and base metal. Tubing of UNS N0820 alloy shall be furnished in the stabilized-annealed condition, Tubing of UNS N0824 alloy shall be furnished in the annealed condition. Tubing of UNS N0826 alloy shall be furnished in the solution-annealed condition. The material shall conform to the composition limits specified. The material shall conform to the mechanical property requirements for tensile strength, yield strength and elongation. Flattening and flange tests shall be made on each end of one tube per lot. SCOPE 1.1 This specification2 covers welded UNS N08020 alloy boiler, heat exchanger, and condenser tubes for general corrosion-resisting and low- or high-temperature service. 1.2 This specification covers tubes 1/8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Table 2 of Specification B751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B468-10(2020) is classified under the following ICS (International Classification for Standards) categories: 77.150.30 - Copper products. The ICS classification helps identify the subject area and facilitates finding related standards.

ASTM B468-10(2020) has the following relationships with other standards: It is inter standard links to ASTM B751-19, ASTM B751-08(2018), ASTM B899-16, ASTM B899-15, ASTM B899-14, ASTM A262-13, ASTM B899-13, ASTM B751-08(2013), ASTM A262-10, ASTM B899-09, ASTM B899-09e1, ASTM B751-08, ASTM A262-02a(2008), ASTM B899-06, ASTM B899-05. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ASTM B468-10(2020) is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.